The lap joint shown supports a weight W equal to 200 lb. The bearing stress and the shear stress should not exceed 18 ksi and 9 ksi respectively. The thickness, t is 1/8 in. Determine the smallest diameter bolt, in inches, that can be used. a. 1/8 b. 5/32 T W + C. 3/16 d. 7/32 BOLT

The lap joint shown supports a weight W equal to 200 lb. The bearing stress and the shear stress should not exceed 18 ksi and 9 ksi respectively. The thickness, t is 1/8 in. Determine the smallest diameter bolt, in inches, that can be used. a. 1/8 b. 5/32 T W + C. 3/16 d. 7/32 BOLT

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: What is the average normal stress at section b-b? 546.1 kPa

Q: Bar AC supports two loads, X = 355 N and Y= 355 N as shown. Rollers at A and Crest against…

Q: Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the…

A: Shear stress of magnesium = 45 MPaShear stress of steel = 75 MPaModulus of rigidity magnesium = 18 ×…

Q: 2. A linkage to an aircraft landing gear is shown. • The 40-kN force acting on the wheel has a line…

Q: A ¼ inch thick steel plate has to be punched with a 1/2 inch holes by applying a force of 40 tons.…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data d=0.75 inP=52 kipsn=5 Here, d is the diameter and P is the load applied. Here, n is the…

Q: A rod of diameter 6 mm is subjected to a tensile load of 15 kN. Then MPa is the value of tensile…

A: Tensile Stress = Load Applied/ Area of Cross Section.

Q: 4. The construction of the post is shown below. The mechanical tube has an OD of 3.0 in and a…

Q: (D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: joint in a wooden structure shown has an applied load F = 50 kN along the axis of the slanted member…

Q: Determine the length of the key to be used based on the compression.

A: Given Data Width of the key b = 32.5 mm Height of the key h = 22.5 mm Diameter of the shaft d = 125…

Q: 19. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630…

A: This question is based on the concept of deformation. As per the guidelines we are subjected to…

Q: 1-What is the average normal stress at section b-b? 546.1 kPa 267.7 kPa 813.8 kPa 779.9 kPa 942.8…

A: Given, W=200 N/m θ=550 The cross-section (square) of AB, a=1.5 cm=0.015 m The diameter of the pin at…

Q: Link AB, of width b= 2 in. and thickness t = in., is used to support the end of a horizontal beam.…

Q: Determine the thickness of a steel air receiver with 30 inches diameter and pressure load of 120…

A: Given, Steel Air Reservoir Inner Diameter = Di= 30 in Pressure = P= 120 psi Design stress= S= 8000…

Q: JA beam is welded to a wall and subjected to a force couple (torsional moment) of 3. 12000 in-Ibs…

A: Given data: The torsional moment on the shaft is, T=12000 in·lbs. The tensile force is, F=5000 lbs.…

Q: 81) A wooden member is joined by means of a glue. The allowable stresses are 600 KPa for shear…

A: We have,allowable shear strength for joint, τallow=600kPa=0.6N/mm2allowable tensile strength of…

Q: Q3/ If two members, A and B, are connected together and fixed supported at one end. The tensile load…

Q: A) Using the ultimate stress found earlier, determine the minimum diameter of post BD required for…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: 1. Two wooden planks each 2 mm. thick and 20. wide, are joined as shown in Figure Q1. Knowing the…

Q: Two portions of member AB are glued together along a plane forming an angle with the horizontal. The…

Q: A hook is to be mounted on a wall as shown. Weight, W, is 2000 N. Shear stress in the bolts should…

Q: Two horizontal 6.42-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: For the rod shown below, determine the maximum normal stress. 350 N 175 N 200 N r= 8 mm 5…

Q: 16. The lap joint shown supports a weight W equal to 300 Ib. The bearing stress and the shear stress…

Q: b. A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: Given Data

Q: 125 mm 75 mm 1.32 Two wooden members of uniform cross section are joined by the simple scarf splice…

A: Given data:

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: The construction of the post is shown below. The mechanical tube has an OD of 3.0 in and a thickness…

A: As per expert Guidelines we are supposed to answer only the first question of the given multiple…

Q: Two horizontal 8.51-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

Q: P P= 1300 KN allowable shear stress in a bolt=210MPa What is the minimum bolt diameter that may be…

Q: Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting 28…

Q: A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A…

Q: Four bolts used to lap joint two steel plates together. Tensile force on the plates is 66.7 kN.…

A: Given data: F=66.7 kNn=4τAllow=68.9 MPa Need to determine the diameter of the bolt.

Q: The lap joint shown supports a weight W equal to 300 lb. The bearing stress and the shear stress…

A: Given data: weight = 300 lb Bearing stress = 18 ksi = 18000 lb/in2 Shear stress = 9 ksi = 9000…

Q: Determine the principal stresses and the maximum shearing stress at point H. (Round the final…

A: At point H, loading will be as per following, M=600(2.5)=1500 lb-inT=600(2.5)=1500 lb-inP=2300 lb…

Q: a clevis acted upon by force P. If the maximum shearing stress is 15ksi, determine the minimum bolt…

Q: For the clevis connection shown, the shear stress in the 0.287-in.-diameter bolt must be limited to…

A: Bolt diameter, d=0.287 inShear stress, τ=29 ksi

Q: Q1. A bracket is to be welded as shown in Fig. if the size of weld s mm, allowable shear stress is…

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.

Question

18. The lap joint shown supports a weight W equal to 200 lb. The bearing stress and the shear stress should not
exceed 18 ksi and 9 ksi respectively. The thickness, t is 1/8 in. Determine the smallest diameter bolt, in
inches, that can be used.
a. 1/8
b. 5/32
W
t
C.
3/16
d. 7/32
BOLT

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: given_data

Step 2: case_1

Step 3: case-2

Solution

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Clutches, Brakes, Couplings and Flywheels

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your units. Knowing that the central portion of the link BD has a uniform cross-sectional area of 1350 mm, determine the maguitude of the load P for which the normal stress in that portion of BD is 20 MPa P= 10.975 kN 24 B I=0.3 m 0.73 m 0.62 m Check Anewer lor the Problum
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given figure. B 100 mm 100 mm 100 mm C 120 mm K A E -280 mm F D Knowing that the turnbuckle has been tightened until the tension in wire AD is 375 N, determine the internal forces at the point K. The shear force Vis 255.86 N. 274.14 N. 1 The axial force Fis The bending moment Mis 84.068 N-m in the counter-clockwise direction.
A pull of 6,500 lb is applied to a steel rod which has an ultimate stress of 65,000 psi. Determine the steel rod diameter if the factor of safety is 5. A. 0.998 inch B. 0.598 inch C. 0.798 inch D. 0.398 inch
1. The frame shown is used to support a window-type air conditioning unit. It weighs 100 lbs and its equivalent weight is applied as shown. Determine the stress in the brace, the deformation of the brace when the load is applied, and the shear stress in the ¼ inch diameter bolts. 14 in 12 in 12 in Brace 1% x % inch steel angles ¼ inch bolt in single shear
B 1 boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi AB cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places 70° 30° 12 ft C Р 4 in. 3.5 in. Detail at A H 0.5-in. dia.
Question 5 of 5 View Policies Current Attempt in Progress For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips. O 27.2 ksi O 37.5 ksi O 25.8 ksi O 21.9 ksi O 35.3 ksi
Two horizontal 6.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 1.8 in.. 60° 45% P P 0.5 in. 1.8 in. С Determine the average bearing stress at C in member BC. The average bearing stress at C in member BC is ksi.
17. The frame shown carries a load P = 2000 lb. If a = b = 10 inches, c = 18 inches, and s= 3/8 inch. Determine the stress in strut BD in ksi. a. 30.5 b. 34.2 a b PA D B C. d. 39.0 46.1 C 22 24 section A-A: Is 18. The motion of the follower of a cam-follower system is governed by x = R(1 + 1/2 cosoot). If R = 70 mm and co = 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 C. b. 20 d.
A set of 10 bolts is to be used to provide a clamping force of 50000 lb between two components of a machine. The load is shared equally among the 4 bolts. Knowing that the grade of the material is SAE Grade 4, if each is to be stressed to 90 %of its proof strength. Then the required tensile stress area is: Select one: A. A, = 0.0714 in В. B. A, = 0.22 in %3D 2. C. A, = 0.0865 in 2. D. A, = 0.0855 in
23. Determine the stress, in MPa, in member DF if its cross sectional area is 900 mm². a. 165 b. 178 4 m a. b. B C 100 KN 6 m 3 m 200 kN 4 m E 3m F O ΟΠΟΙΟΙ C. d. 24. Determine the largest load (in kN) that a 8 mm pin can support if it is in single shear and the working stress is 160 MPa. 16.1 32.2 214 250 C. d. 48.0 Answer is not among the choices
A 60 m long steel cable was stretched by 60 mm when load was applied to both ends. Determine the modulus of elasticity if the tensile stress is 205 MPa. A. 305 GPa B. 205 GPa C. 495 GPa D. 505 GPa