23. Determine the stress, in MPa, in member DF if its cross sectional area is 900 mm².a.165b. 1784 ma.b.BC100 KN6 m3 m200 kN4 mE 3mFOΟΠΟΙΟΙC.d.24. Determine the largest load (in kN) that a 8 mm pin can support if it is in single shear and the working stress is160 MPa.16.132.2214250C.d.48.0Answer is not among the choices

Since you have posted multiple questions, we will provide the solution only to the first question as…

Answered: 23. Determine the stress, in MPa, in…

23. Determine the stress, in MPa, in member DF if its cross sectional area is 900 mm². a. b. A 165 178 4 m B C 100 KN 6 m 3m 200 KN D 4 m E 3m F C. d. 214 250

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your units. Knowing that the central portion of the link BD has a uniform cross-sectional area of 1350 mm, determine the maguitude of the load P for which the normal stress in that portion of BD is 20 MPa P= 10.975 kN 24 B I=0.3 m 0.73 m 0.62 m Check Anewer lor the Problum
The cantilever beam is loaded as shown. P1, P2 and a are 20 kN, 50 kN, and 600 mm. Determine the maximum normal principal stress, in MPa, in the beam. a. b. P₁ # 145 156 P₂ # ht 50 mm 75 mm C. d. 168 184
1.25 ft 3. Determine the maximum allowable weight of passengers on the gondola ride which is suspended from roller E. The down arm EA is made from 1.5" square solid steel with an allowable normal stress of 18 ksi. The center of roller E to the center of section DC is 1.25'. 4 ft 1.5 in.- B 1.5 in.- 5.5 ft A
A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the amount of stress on each cable.
B 1 boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi AB cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places 70° 30° 12 ft C Р 4 in. 3.5 in. Detail at A H 0.5-in. dia.
Determine the maximum principal stress (in ksi) for the state of stress at a point shown below. a. b. 37.1 47.1 40 ksi 30 ksi 80 ksi C. 57.1 d. Answer is not among the choices
shown. P1. Two solid circular rods are welded together at B as Determine the normal stress in each rod. 64 mm Ø1 20 KN 38 mm Ø 1.0m 40 KN 40 KN B t Fig.pl-01 1.5 m C whose
The turnbuckles in the diagram shown are tightened until the compression block DB exerts a force of 12,365lb on the beam at B. Member DB is a hollow shaft with an inner diameter of 1.0 inch and outer diameter of 2 inches. Rods AD and CD each have cross-sectional areas of 1.1 square inches. Pin C has a diameter of 0.78 inch. Determine the following: a.The axial stress, in psi, in BD. b.The axial stress, in psi, in CD.c.The shearing stress, in psi, in pin C.
Two horizontal 6.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 1.8 in.. 60° 45% P P 0.5 in. 1.8 in. С Determine the average bearing stress at C in member BC. The average bearing stress at C in member BC is ksi.
please
The U-bar shown below has a circular cross section with a diameter of 1 in. For the loading shown, determine the maximum and minimum normal stresses on a cross section between A and B. 500 lb- A B 2₁ 4 in 500 lb
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8