boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi ● cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi ● the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places

boom AC is a 4-in. square steel tube with a wall thickness of 0.25 inch and the allowable stress is 25 ksi ● cable BC is 0.375 inch in diameter and the allowable stress is 18 ksi ● the pin at A is 0.5 inch in diameter and the allowable shear stress is 14 ksi Determine the largest safe load P. Answer in lbs. rounded-off to 2 decimal places

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
4. two decimal places
Question 6 Two identical plates of 63 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 29 kN, determine the maximum tensile stress (MPa) developed in the plate.
A 600 kg material is hung from the end of the horizontal bar BD as shown. Determine the stress on the rod AC if its diameter is 25mm. Use 2 decimal places in every solved values.
Two horizontal 6.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 1.8 in.. 60° 45% P P 0.5 in. 1.8 in. С Determine the average bearing stress at C in member BC. The average bearing stress at C in member BC is ksi.
The lap joint is fastened with four 0.79-in.-diameter rivets. The working stress is 17.27 ksi for the rivets in shear. Find the axial load P (in lb) that can be applied to the joint. Assume that the load is equally distributed among the rivets. Round off the final answer to two decimal places.
The cantilever beam AB will be installed so that the 60-mm side forms an angle β between 0 and 90° with the vertical. The 660-N vertical force P is applied at the center of the free end of the beam. Determine the value of β for which the normal stress at point a is a maximum and the corresponding value of that stress. (Round the final answer to two decimal places.)
For the hoist shown below, when the weight W is 7000, lb, the tension in AB is 13,000 lb. Determine the shear stress in the 1 inch diameter pin at A which is in double shear: ____ lb/in2. Calculate your answer to 1 decimal place.
The two pieces of wood, 2.59in. by 5.69 in., are glued together along the 60°joint. Determine the normal stress (in psi) in the glue if the shear stress in the glue is limited to 352 psi. Round off the final answer to three decimal places. 017 shear.png ... P A
Joints B and D use a pin with a diameter of ø10 mm. In connection C, the diameter of the pin is ø6 mm. The permissible shear stress τmax of the pins is 75 MPa and the permissible normal stress σmax of the rod BD is 200 MPa. Determine the maximum allowable value of the force P. Units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer! Dimension L = 250 mm
Two horizontal 5.82-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.68-in. diameter is used at each connection, determine the bearing stress (in psi) at Bin member AB. Round off the final answer to two decimal places.
Show your complete solution and make sure that your finals answer is in 4 decimal places, please make it readable.