81) A wooden member is joined by means of a glue. The allowable stresses are 600 KPa for shear strength of the glued joint and 900 MPa for tension in the glued joint. Also, the allowable tensile stress for tension is 1 MPa for the solid wooden material. Determine the safe value of P. The wooden section is 50 mm by 150 mm. P. 50 mm glued joint

81) A wooden member is joined by means of a glue. The allowable stresses are 600 KPa for shear strength of the glued joint and 900 MPa for tension in the glued joint. Also, the allowable tensile stress for tension is 1 MPa for the solid wooden material. Determine the safe value of P. The wooden section is 50 mm by 150 mm. P. 50 mm glued joint

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I need to solve the question within 10 minutes.
A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing stress in each rivet. (b) the bearing stress in each plate. (c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally among the three rivels. equally among the three rivels. To o o P 20 mm -25 mm P.
Required information A 920-mm (4) strip of steel (E= 200 GPa) is bent into a full circle by two couples applied as shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. M' M mm Determine the maximum thickness t of the strip if the allowable stress of the steel is 420 MPa. The maximum thickness t of the strip is mm.
Two aluminum plates, each having a width of b = 8.0 in. and a thickness of t = 0.750 in., are welded together as shown. Assume a = 4.0 in. For a load of P = 75 kips, determine (a) the normal stress that acts perpendicular to the weld and (b) the magnitude of the shear stress that acts parallel to the weld. Answer: O= P T = 1 i 1 ksi ksi b P
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
Two horizontal 6.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each connection. 0.5 in. 1.8 in.. 60° 45% P P 0.5 in. 1.8 in. С Determine the average bearing stress at C in member BC. The average bearing stress at C in member BC is ksi.
STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm wide and 20 mm thick are glued together as shown. If P is 600N, the shearing stress in the glued joint is
The timber member has a cross-sectional area of 1850 mm? and its modulus of elasticity is 12 GPa. What is the normal stress in member AB? 40 kN 35 kN 20 kN D A B +1.5 m→ - 3 m - - 3 m · Select one: O a. 8.11 MPa b. 10.81 MPa с. 13.51 MPа d. 21.62 MPa
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8
QUESTION 2 1.2 A thin cylindrical pressure vessel has the following specifications Internal pressure 5.33 MPa Metal thickness 20 mm Maximum allowable stress 120 MPa Efficiency of the longitudinal joint Efficiency of the circumferential joint 80 % 50 % 1.21 Determine the maximum internal diameter which the cylinder may have. 1.2.2 The actual values of the hoop and longitudinal stresses. For the soolbar, press ALT=P10 (PC) or ALT-FN-F10 (Mac). B IUS Paragraph Ara !! 140x AITZAN LAINA
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?