1-What is the average normalstress at section b-b?546.1 kPa267.7 kPa813.8 kPa779.9 kPa942.8 kPaNone2-What is the average shear stressat pin A, given its diameter as 8mmand assuming double shear casefor the pin?3.6 MPа2.6 MPа5.2 MPa3.9 MPa1.8 MPaNone In the mechanism shown below, thedistributed load W is 200 N/m and theangle e is 55°, knowing that link AB has1.5cm x 1.5cm cross-section.WB1.5 m ea1-What is the average normalstress at section b-b?546.1 kPa267.7 kPa813.8 kPa779.9 kPa942.8 kPaAlere

Given, W=200 N/m θ=550 The cross-section (square) of AB, a=1.5 cm=0.015 m The diameter of the pin at…

1-What is the average normal stress at section b-b? 546.1 kPa 267.7 kPa 813.8 kPa 779.9 kPa 942.8 kPa None 2-What is the average shear stress at pin A, given its diameter as 8mm and assuming double shear case for the pin? 3.6 MPа 2.6 MPa 5.2 MPa 3.9 MPа 1.8 MPa None

1-What is the average normal stress at section b-b? 546.1 kPa 267.7 kPa 813.8 kPa 779.9 kPa 942.8 kPa None 2-What is the average shear stress at pin A, given its diameter as 8mm and assuming double shear case for the pin? 3.6 MPа 2.6 MPa 5.2 MPa 3.9 MPа 1.8 MPa None

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ___ MPa. 6.80 1.50 3.20 4.30 8.10
مقاومه HW2
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the diameter (mm) of the A premium?
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
Asap within 20 mins will voteup
A shear force of V = 240 kN is applied to the box girder. (Figure 1) Figure Part A 9A= 28.82 Part B 200 mm B 90 mm μÅ LO 9B = 16.42 200 mm 10 mm. A μÅ C D 180 mm Determine the shear flow at point A. Express your answer to three significant figures and include the appropriate units. MPa 90 mm Submit Previous Answers Request Answer 100 mm 190 mm -10 mm X Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units. MPa Determine the shear flow at point B. Express your answer to three significant figures and include the appropriate units. ? Pocke Submit Previous Answers Request Answer 1 of 1 ? > Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units.
A pin connection, like that shown in Figure -16, is subjected to a force of 16,5 kN. Determine the shear stress in the 12.0 mm diameter pin.
20 A force of 250 kN was needed to punch the hole through the 8 mm thick steel plate, as shown below. rosesloyotoled jau milubase Ø24 Farhododecirl most soumis SALP30 TOUREN stav (A) 76.11 MPa (B) 97.66 MPa (C) 203.75 MPa (D) 399.06 MPa Hora 100 39 Calculate the ultimate shear stress of the steel plate. 60 bobini dignoue Mould 10.00 (0) gnitroo ni beau Pefore on OV1 es des anglet of quilida fins lidi.is (8) constalter goisons (2) in boe migjow tigilan (0)
NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
W=1
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P