The cross section of a bar made of cartridge brass is a hexagon. Find dimension a if the allowable stress is 85 MPa and the tensile load is 350 kN. [cm] If the bar in problem #3 is 2.5 m long and the allowable change in length is 1.5 mm, what is the required dimension a? [cm]

Q: Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity of water is…

A:

Q: Q 3) A fluid in a cylinder is at pressure of (101.526 psi). It is expended at constant pressure from…

A:

Q: draw isometric diagram with measurement labels

A:

Q: Question 4: Determine the displacement of the log if the truck at C pulls the cable 4 ft to the…

A:

Q: not read the answer. Is there a way to upload it in ano

A: Navier-stokes equation (momentum and continuity equations)

Q: Hi please help with this question thank you I just can't seem to work it out even with the given…

A: Given Data σx,=31.5MPaσy,=45.5MPaτx,y,=20.5MPa

Q: A satellite is launched from earth such that the booster burnout occurs at an altitude of 422 km…

A: Given data: Burnout occurs at an altitude, h=422 km Velocity, vo=9.5 km/s=9500 m/s, Flight path…

Q: For 10-2 above, the last part of Step 6 and the final answer seems to be missing or cut off on my…

A:

Q: using the sine bar technique, find the value of the angle for the given data: the stacked height was…

A:

Q: I am unsure of how the equation got to the final result.  Can you elaborate on the steps between the…

A:

Q: Given Values Heater core surface temp Heater core diameter Thermal conductivity of sleeve Sleeve…

A:

Q: Turbofan thrust specific fuel consumption is c =0.57 lb/ (lbf.hr). The turbofan engine generates…

A: Given data,

Q: 66 Through holes Through hole 70 sketch the orthographic view using catia v5, and i need the…

A:

Q: Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a…

A:

Q: Which among the following is/are vector quantites? (No partial points.) Velocity Distance Position…

A: Vector quantities are one which has both magnitude and direction.  Scalar quantities are one which…

Q: For the beam shown find the deflection at point B ft and D ft if El=2200kip.ft? by using the…

A:

Q: A regular tetrahedron of side length 0.5 m has black internal surfaces with the following…

A: INTRODUCTION : The heat transmission from the different sides of the regular tetrahedron and the…

Q: Find the velocity of the block when va 4 [m/s]. Va BLOCK

A:

Q: Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and…

A: To find Determine the minimum diameter, d for the rod that will achieve a minimum static factor of…

Q: Question 3: A block moves outward along the slot in the platform with a speed of (4t) m/s, where t…

A:

Q: 1. The beams are wooden, size 150mm x 50mm, quality C24, E-module=11 kN/mm, maximum shear stress for…

A: **According to the guidelines we can answer only three subparts of a question, Please resubmit the…

Q: Are the location dimensions in Question 4 placed using base line or chain dimensioning?

A: Given figure

Q: Draw Top, Front and Right view of the following isometric drawing. R35 Ø22 28 80 110 46 70

A:

Q: Insulation T₂1 h₁ T Steam T₂ h₂ T=₂ T₂ www R₁ R₂ R₂ T=₂ R₁ °C flows in a cast iron pipe (k = 80 W/m.…

A: The diagram of the above thermal condition is shown below, using the equivalence with electrical…

Q: Consider the following dataset and separator. What is the width of margin (distance between the two…

A: Write the given expressions. wx+b=+1     ...... (1)wx+b=0       ...... (2)wx+b=-1    ...... (3)

Q: For the figure as shown below, find h in cm that will result to a pressure difference (PA PB) of 10…

A:

Q: 3 Th To = 293 K V Room temperature T. emperature changes from Th to T during process 3. The cartoon…

A:

Q: Simplify the following expressions (note that dij is the Kronecker delta, repeated index means…

A: a) The Kronecker delta is equal to 1 if the indices are equal and 0 otherwise. Therefore, δtt = 1.…

Q: 4-53 The supporting structure of the billboard is attached to the ground by a pin at B, and its rear…

A:

Q: Using the Creo parametric sketch the following: GIVEN - PICTORIAL VIEW DRAW- THE ORTHOGRAPHIC VIEW…

A: given : pictorial view

Q: A 1-in, constant diameter shaft, is loaded with forces at A and B as shown, with ground reaction…

A: To findDetermine the factor of safety usingthe maximum shear stress failure theory.The distortion…

Q: The mechanism below is analyzed as a pin-jointed four bar linkage. The link 2 (O₂A) is the input…

A:

Q: Given the views below, sketch the isometric figure . You may use @ut0c@d to draw the figure

A: we need to draw the isometric view with the help of the given three orthographic projection views.

Q: 10. The 20-mm-diameter A-36 steel rod is subjected to the axial forces shown. Determine the…

A:

Q: 1a. Consider the problem 2-15 from Ozisik (1993). Starting with the heat diffusion equation, Eq.…

A:

Q: 17. What type of scale is shown? a. Arbitrary b. Differential How much did you like the conference?…

A: Given question is : What type of scale is shown?       The given question is related to Industrial…

Q: can you please do the quadratic interpolaton on paper so I can see how you did it

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.