Question 4: Determine the displacement of the log if the truck at C pulls the cable 4 ft to the right.

Q: Water is flowing in a pipe with radius of 25.4 cm at velocity of 5 m/s. The viscosity of water is…

A:

Q: Row indexing: Snow fall records stateSnowRecord contains the amount of snow fall (in cm) for various…

A: Based on the problem statement, it seems that the task is to implement a function called…

Q: (3) Use the following graph to answer the questions on this page. The total time is 0.4 seconds.…

A: Solution:

Q: The acceleration of an object is proportional its velocity its mass its position its displacement…

A: As per our guidelines, we are supposed to answer only first one question in case of multiple…

Q: For Questions 3 and 4: A cup of water was heated to a temperature of 90°. It was placed in a…

A: Given, The temperature of the liquid, L = 17°C The temperature of surroundings, S = 11°C Initial…

Q: 7. Why are land and groove markings on a bullet considered Class Evidence, while the striation…

A: why are land and groove marking on a bullet considered class evidence. while the striation marking…

Q: Newton's Law of cooling states that the rate at which heat is lost by a heated body is proportional…

A:

Q: For the Following question Graph all 4 : [I just need all 4 graphs and please explain and make clean…

A: Given that, a=50 et550v=et-111x=et-t-111 (1) Drawing position vs time as shown below,

Q: For 10-2 above, the last part of Step 6 and the final answer seems to be missing or cut off on my…

A:

Q: using the sine bar technique, find the value of the angle for the given data: the stacked height was…

A:

Q: I am unsure of how the equation got to the final result.  Can you elaborate on the steps between the…

A:

Q: A box slides down a chute, which is bent in the shape of a hyperbola (Figure 3). When the box…

A:

Q: Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and…

A: To find Determine the minimum diameter, d for the rod that will achieve a minimum static factor of…

Q: A motorcyclist left from his work at 5:45 in the morning and arrived at the coffee shop 42 km away…

A:

Q: Question 3: A block moves outward along the slot in the platform with a speed of (4t) m/s, where t…

A:

Q: The maximum force a plastic grocery bag made from low-density polyethylene (LDPE) can withstand…

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: Newton’s 2nd Law Lab (Modeling­ friendly lab)   Go to the PhET simulation Forces & Motion.…

A: Given: Choose a mass at the beginning, and keep it constant for this entire experiment. Set the…

Q: Please refer to the attached picturs of the problem statement. I have solved a, b, c, and g using…

A: Given:  For part d.Vinitial=V0distance between front of the crate and front of the…

Q: 4-53 The supporting structure of the billboard is attached to the ground by a pin at B, and its rear…

A:

Q: Using the Creo parametric sketch the following: GIVEN - PICTORIAL VIEW DRAW- THE ORTHOGRAPHIC VIEW…

A: given : pictorial view

Q: Posted below is a picture of a data table and a diagram of an experiment. In the experiment you…

A:

Q: A 1-in, constant diameter shaft, is loaded with forces at A and B as shown, with ground reaction…

A: To findDetermine the factor of safety usingthe maximum shear stress failure theory.The distortion…

Q: Given the views below, sketch the isometric figure . You may use @ut0c@d to draw the figure

A: we need to draw the isometric view with the help of the given three orthographic projection views.

Q: Directions: Use the appropriate equation to recorded below or in your Engineering Design journal.…

A: This question is based on the concept of lever, effort and load.

Q: You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular…

A: Given: Load = 1000 N L = 150 mm t = 4 mm w = 15 mm To find: Shear force and bending moments for…

Q: Please provide equations that you are using so I can follow along and learn how to do this and…

A:

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.