The following graph shows a load-extension graph on a polymer specimen 15mm in diameter and 45m rightmost datapoint represents the reading at the p fracture.

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Convert 3 centimetres (cm) to millimetres (mm)

A: Given data: Unit = 3 centimetre Need to convert into millimetre.

Q: If A = Gax + 3a, and B = 8'ax + 2ay-8 az, %3D (a) find the dot product (b) find OAR

A: GivenA→=6i^+0j^+3k^andB→=8i^+2j^-8k^

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: How many balls of 30 mm diameter fit in a volume of 1.91 m^3

A: Given data: ● The total volume of space:  V = 1.91 m3 ● The diameter of the single ball: d = 30 mm =…

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: 3.00- 1.25-

A:

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: A part may be properly represented on an engineering drawing with as few views as: A. one B. two…

A: Please find the answer in the next page.

Q: Figure 3 shows a product of tennis ball launcher in the market. Determine the problem statement,…

A:

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: ood day. I am trying to review for examinations and require assistance for these questions... Horse…

A: Given

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the…

A: Weight of full spool = 2038=1638 ouncesEmpty Spool weight = 114 = 108 ounces

Q: organize the answers pls.

A:

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: How many balls of 70 mm diameter fit in a volume of 1.91 m^3

A: Given data Diameter of ball = 70 mm Total volume = 1.91 m^3 Brief introduction First determine…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: A rectangular tank measures 1.2 meters long, 1 meter wide and 2 metres high. What is the volume, in…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: 1. show all steps in detail, units and formulas please.

A:

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: Draw the sectional view of the solid and provide necessary dimensions. E 7 Scale 1:2 Draw the…

A: According to the given datatwo object views are givenWe need to draw the section view of the problem

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.