of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the catalog as 2 1/4 ounces per 100 feet. An empty spool of the roll weighs 1 1/4 ounces. If the roll to be inventoried weighs 20 3/8 ounces, what is the approximate amount of wire on the spool in feet?

Q: What is the weight of 3 slug, expressed in pounds-force? 96.522 lbf

A:

Q: The family traveled to Florida for vacation. When you arrived, the trip meter read 486. New tires…

A: Total distance travelled=486 miles                                       = 486*63360 inches…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: how to you get the Q1 = 70.3

A: In this problem, it is asking how did we get Q1=70.3 kJ/kg.

Q: A bookshelf needs to be built to hold 200 novels.  The depth, width and height of the largest novels…

A: Number of books Dimension of largest book = depth x width x HeightLet's assume all 200 books are of…

Q: What is the weight of 12 kilogram object, expressed in lbf? 26.424 o lbf

A: Recall:- 1 kilogram = 2.20462 lbf  Weight of the object (W) = 12 kilogram

Q: A dumbbell is suspended by two cables, where 0 = 46° and T ||T|| Determine the approximate weight of…

A:

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: A Prony brake with a 12” arm is applied to an engine flywheel. At 1200 rpm, the scale registers 20…

A:

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: Find the volume of the propane tank.

A: Given:- Drawing of a cylinder Material:- AISI steel 1020  To find:- Volume of tank

Q: The measurement 0.000 004 3 m, expressed correctly using scientific notation, is

A: Scientific notation  0.0000043 m = 4.3 *10^-6 m

Q: 37. Show the tolerance zone for the given slot. Superimpose the tolerance zone on the given drawing.…

A: Given, The tolerance for the offset is T=±0.02 units So, the thickness of the tolerance zone is…

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given    Wind power generated, P = 1.3 MW                 Power coefficient = 025

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A:

Q: A spring is 15 in. long when loaded with 16 lb and 6.5 in. long when loaded with 25 lb. Determine…

A:

Q: 1. show all steps in detail, units and formulas please.

A:

Q: Find the fluid force on the vertical side of the tank, where the dimensions are given in feet.…

A: Given data Weight density = 62.4 lb/ft^3 Find the force on vertical side of tank.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.