A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 uɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage B. D H. 2 b.

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 uɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage B. D H. 2 b.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 GPa, Ebrass = 100 GPa and Esteel=250 GPa. Determine, (а) The internal forces for each segment (AB, BC and CD) by showing appropriate free-body diagram, FBD. (b) The total strain energy in the whole rod assembly AB, BC and CD.
3. The 3-meter long T-beam pictured on the far right is placed flange downwards and subjected to the loading shown below. Sketch the moment diagram and calculate the maximum compressive and tensile bending stresses. 12 kN/m m 18 kN/m] B 30 mm C. B 150 mm M 150 mm 300 mm 30 mm
1. At a critical point on the free surface of a loaded beam, the strains are measured in three directions at 0, = 0°, 0,=45, 0̟=90° (see Fig. 1). They are found to be -10, +5×10³, +10´, respectively. a) Calculate the magnitude and orientation of the principal strains at the point. b) If E = 120 GPa, v=0.3, find the magnitude of the principal stresses. c) Determine the directions of the principal planes. 90 45° Fig. 1 2. A sheet of material is subjected to a two-dimensional stress system in the x-y plane. At a given point, an element with its sides parallel to x and y axes is found to have a shear strain of 1×10, while an element at 45° to the first has a shear strain of 4×10 (Fig. 2). a) Calculate the maximum shear strain at this point. b) If the shear modulus 100 MPa, find the difference between the two principal stresses. y =4x104 D F6 F8 F9 F10 F11 F12 & 69
A cylindrical rod of an isotropic material with a diameter (d0) of 16 mm is loaded with a 5,700 N load along its major axis. If the material has a Young’s modulus (E) of 120.0 GPa and shear modulus of elasticity (G) of 40.9 GPa, what is the strain vector for an axis rotated 20 degrees counter-clockwise about the z-axis.
Parvinbhai
A small aluminum alloy [E = 75 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b = 21 mm, d= 32 mm, and t = 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 µɛ is measured from a strain gage located at c = 7 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P P ЗР C Strain gage- d E H b Answer: P = i N /2
Mechanics
a) Draw the stress-strain diagram for an ELASTIC-PERFECTLY PLASTIC material.b) A simply supported steel beam AB is given a point load P at the location of 1 m from the left of B. The yield stress and elastic modulus of the material are o-y = 210 MPa and E = 200 GPa, respectively. The material behaves linear elastic-perfectly plastic. If the elastic core = 20 mm at the most critical location, find
2. An Aluminum-alloy block is loaded as shown in the figure. The application of this load produces a tensile strain of 500 x 10 at gage A. Calculate the magnitude of the applied load P. Let E = 100GPa 400mm 120 Gage A P 20mm
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.20 in., -0.55 in.). Assume a = 9 ft, b = 6 ft, and h = 7 ft. Determine the normal strain in each bar. B P b h
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
A 45° strain rosette (see figure) mounted onthe surface of an automobile frame gives the followingreadings: gage A, 310 X10-6 ; gage B, 180 X10-6 ;and gage C, -160X10 -6 .Determine the principal strains and maximumshear strains, and show them on sketches of properlyoriented elements.