66 Through holes Through hole 70 sketch the orthographic view using catia v5, and i need the orthographic view in the first angle projection also provide the isometric view

Q: Use Scale ( 1:1), for the front and side views shown draw the isometric projection 50 30 25 40 80 30…

A: Isometric projection of an object is defined as a method of representing a 3-dimensional object in a…

Q: Draw the orthographic view of the following component mention top view ,side view,front view

A:

Q: Draw the three projections of the following figure using AutoCAD software and send the solution in…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Sketch the three view of the given view using creo and also show the hidden line of the attached…

A:

Q: for the following isometric component ,sketch the orthographic view

A:

Q: provide Orthographic view

A: Question fig.

Q: Give all the location dimensions between the datum target points, B1 ,C1 and B2, C1. B1, C1 : X =…

A: Since, the bottom part of the drawing represents dimensions in X and Y direction while the upper…

Q: Consider an overall drawing made up of objects (full or hollow rectangular parallelepipeds; with or…

A:

Q: C.) J= A oC toB-D E d) k=G-0F+oD-OCTOB FYl= o = min +0 = Prus Pous

A: Write the all vectors.…

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: sketch the figure using autocad 2021. use necesary dimension and colours

A: start making the three linear cicles as in center of the figure

Q: skech the 3 projection views and the isometric view

A: The three projection views are the Top view Front view side view.

Q: Draft and annotate the 2D sketch of upright using AutoCAD and mention all the dimensions. Colour the…

A:

Q: 7 6 5 сл 4 3 2 1 Work to be done: Reproduce this object in isometric perspective at a scale of 1:50…

A:

Q: 2 Cot x 3 Isinx+1)(2Cosge-)=0 1)(2cOS以-1)

A: In this problem, we have to prove  sinx+12cosx-1=0   ...... (1)when cot2x=3

Q: Sketch the Orthographic and  auxiliary view

A:

Q: Show the working view ,help me by showing step by step to sketch the orthographic view of the…

A: open creo parametric software then open new  part , sekect the XZ plane and edit the skecth and draw…

Q: draw the orthographic view of the above given sketch note using catia v5 software

A:

Q: 1. Sketch the CAVALIER OBLIQUE of the given object. Use corner "A" for orientation.

A: according to the details provided in the question, we need to draw a cavalier view of the given…

Q: Draw the figure below by using the appropriate 3d commands, rectangular array, and other operations…

A: 3D angular array

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: Draw the following views in Orthographic Third Angle Projection. 10:35 am 20 80 20 10:35 am

A: Given Data: Isometric view of the figure

Q: Consider that we have a 3-R robot as shown in the figure below. The lengths of the links are:…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: This prelab question is about the experimental setup shown in the Lab Manual as Figure 1 for…

A: In theory we assume ideal conditions (that are not practical or applicable in real world). Hence…

Q: Galileo's first telescope used the arrange- ment shown in the figure to the right, with a…

A: The given lens arrangement is that of galileo telescopic lens. the ray diagram depicting that final…

Q: Pls show the edge view of two triangles in a single reference plane...kindy explain the steps

A: Solution: Given Data:

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 50 30 25 40 80…

A: Isometric projection of an object is defined as a method of representing a 3-dimensional object in a…

Q: Sketch the orthographic view of the following figure

A: the isometric view is drawn as shown below

Q: Use Scale ( 1:1), for the front and side views shown draw the isometric projection 10, -R25 30 35…

A: In technical and engineering drawings, isometric projection is a method for graphically depicting…

Q: mechanical engineering : engiineering drawing  exercise sketch the figure using autocad 2021…

A:

Q: sketch the standard orthographic view ,using CATIA V5

A:

Q: sketch the 2d figure using AutoCAD and mention the giwn dimensions

A:

Q: finishing the program of the part by using SKY CNC system format R4 O 40 Ø32 Ø24

A: N10 T2N20 G92 S1200 M42N30 G96 S150 M04N40 G00 X-1 Z5 M08N50 G01 Z0 G42 F0.2N60 G01 X24 C2N70 G01…

Q: ☆Draw figures 1 and 2 using AutoCAD and store the drawings in red at the command of Block

A:

Q: Redraw the given orthographic views in full scale (1:1) and the corresponding section view. On…

A: Please refer the next page to see the section view.

Q: The given sketch is a cross section view of "Housing". Sketch the 2D sketch of the below figure…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.