The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a clockwise moment of 120 N-m is needed to tighten the nut at A and the extension d = 300 mm, determine magnitude of force F required to develop this the 300 mm 30° 15 F

The connected bar BC is used to increase the lever arm of the crescent wrench as shown. If a clockwise moment of 120 N-m is needed to tighten the nut at A and the extension d = 300 mm, determine magnitude of force F required to develop this the 300 mm 30° 15 F

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 21 A flanged bolt coupling, consists of 20mmo rivets arranged, is used to transfer the Torque T from a solid shaft 80mm in diameter to a 180mm square hollow tubular pipe with unknown thickness T. 3) Determine the maximum applied torque T without exceeding a maximum shearing stress of SOMPA for circular shaft, and 60MPA for the rivets. Gun =83 GPa. 4) Determine the minimum thickness "T" of the tubular pipe with a maximum shearing stress of 70 MPa. 5) Assuming point B is fixed, and the shaft A-B is 300mm long, determine the angle of twist developed at A relative to B. R10 R125 R80 OBT
The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter of 0.753 in. If a force of 15 kip is applied to the bar, determine the angle of tilt of the bar in degrees. 3.5 ft 2.5 ft E D -1.25 ft- 0.75 ft' 1 ft 15 kips
W weight 74N, reaction force on K wheel is one third of w. (1/3). In this case, find the load on the bars HIJ, GL, CL and FC. The rollers are frictionless.
For a helical spring the slope of helix may be assumed small, is required to transmit a maximum pull of 1 kN and to extend 10 mm for 100 N load. The mean diameter of the coil is to be 100 mm. The diameter of wire is 100 mm. Calculate the no. of coils required? (G = 100 GPa and fs = 100 MPa)
Determine the force in member DE and in the counters that are acting when P₁ = 7 kips and P₂ = 13 kips. Counters ABA A B P₁ E F The force in DE is The force in counter BE is The force in counter DG is G P₂ 8 ft → kips. ((Click to select) ✓ H kips. ((Click to select) kips. (Click to select) T 6 ft
I need this problem to be solved by the force method.
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) A prybar is used to remove a nail as shown. Determine the moment of the 240 N force about the point O of the contact between the prybar and the small support block. (in N-m)
Strength of materials A cast-iron crank has a section on the line AB of the form shown. Show how to determine the greatest compressive and tensile stresses at AB, normal to the section, due to the thrust P of the connecting rod at the angle shown. If the stresses at the section must not exceed 75 MN/m2, either in tension or compression, find the maximum value of the thrust P.
The solid 25 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 700 N, Q = 950 N, LAB = 600 mm, LBC = 1050 mm, LCD = 1050 mm.
The 160-N force is applied as shown to one end of the curved wrench. If a = 38°, calculate the moment of F about the center O of the bolt. Determine the value of a (0 < a < 90°) which would maximize the magnitude of the moment about O; state the value of this maximum moment. The moments are positive if counterclockwise, negative if clockwise. F = 160 N A 21 mm 61 mm 156 mm 61 mm 21 mm Answers: Mo = 51.64308 N-m Momax = i 47.16694 N-m when a = 30.54