Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. *** Dimensions in mm 180120- 60 kN CI 1.00 100 DI E 40 kN 40-mm diam, 30-mm diam.

Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. *** Dimensions in mm 180120- 60 kN CI 1.00 100 DI E 40 kN 40-mm diam, 30-mm diam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

LL Determine the deflection (negative if downward) of the beam at B. Use G-200 GPa and I= 500(10)6 mm. Answer in mm rounded-off to 2 decimal places. P = 29 KN 144H 3 m- P B - - 4 m 2P C H -3 m- acer
Badly needed
04. The load Q is gradually increased from zero to 120kN. a) Does failure occur in bars BE and BD? b) Determine the maximum deflection at pointB. a = 0.64m Square Cross-Section 10mm x 10mm 1.7m E A36-Carbon Steel A36-Carbon Steel 2.64 m OD for all pins = 6mm
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.
A cantilever beam (member AC) is supported with a column (member CD). Force P is applied to Point B, which is located at the midspan of the beam AC. The column is required to prevent excessive deflection of the beam as shown below. Determine the ratio of internal force in the column (member CD) to the critical buckling load of the column (Pcr). The length for both of the members, L, is 1,650 mm. The applied force, P, is 240 kN. The flexural rigidity for the beam and the column, EI, is 4.0X107 kN·mm2.
PLATE NUMBER 9 TITLE: DOUBLE INTEGRATION МЕТНOD OBJECTIVE: TOo SOLVE THE BEAM USING DOUBLE INTEGRATION МЕТНOD 10kN 15KN 5kN 35kN/m 10KN/m 百 3m 3m 3m 10m 1. Solve the deflection at B. 2. Solve the deflection at C. 3. Solve the deflection at D. 4. Solve the location of the maximum deflection. 5. Solve the maximum deflection.
2.3.5
The 100 N block hits the simply supported beam at its mid span after a drop of 10mm as shown in the figure, consider flexural rigidity of the beam as 1728N-m². The dynamic deflection (in mm) at mid span is (a) 6.86 (c) 4.38 100N W 0.6m 10mm 0.6m (b) 8.86 (d) 6.34
The wire AE is stretched between the corners A and E of a bent plate. Knowing that the tension in the wire is 435 N, (a) Determine the moment about each of the coordinate axes of the force exerted by the wire on corner A (b) Determine the moment about the axis OE of the force exerted by the wire on corner A. 160 mm 120 mm 90 mm E 120 mm B D
The wire AE is stretched between the corners A and E of a bent plate. Knowing that the tension in the wire is 435 N, (a) Determine the moment about each of the coordinate axes of the force exerted by the wire on corner A (b) Determine the moment about the axis OE of the force exerted by the wire on corner A. 160 mm 120 mm 90 mm E 120 mm B D
Members AB, BC, and CD are rigidly attached at their ends. All members are made of steel (E=200GPa). Determine the required load P such that the total deflection is equal to 0.5mm shortening.
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft