2.136 The air velocity in the duct of a heating system is to be measured by a Pitot-static probeinserted into the duct parallel to the flow. If the differential height between the water columnsconnected to the two outlets of the probe is 2.4 cm, then the flow velocity (in m/s) at the tip ofthe probe isThe air temperature and pressure in the duct are 45°C and 98 kPa,respectively. Take the density of water to be p = 1000 kg/m³ and the gas constant of air is R =0.287 kPa m³/kgK. (Correct up to one decimal place)

Answered: Image /qna-images/answer/bdf21281-02d5-41dc-a37b-7af7af49cc04.jpg

The air velocity in the duct of a heating system is to be measured by nserted into the duct parallel to the flow. If the differential height between connected to the two outlets of the probe is 2.4 cm, then the flow velocity he probe is The air temperature and pressure in the duct ar respectively. Take the density of water to be p = 1000 kg/m³ and the gas c 0.287 kPa m³/kgK. (Correct up to one decimal place) C

The air velocity in the duct of a heating system is to be measured by nserted into the duct parallel to the flow. If the differential height between connected to the two outlets of the probe is 2.4 cm, then the flow velocity he probe is The air temperature and pressure in the duct ar respectively. Take the density of water to be p = 1000 kg/m³ and the gas c 0.287 kPa m³/kgK. (Correct up to one decimal place) C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.0. I Rd 5. A horizontal Venturimeter with inlet and throat diameters 300 mm and 100 mm respectively is used to measure the flow of water. The pressure intensity at inlet is 130 KN/m2, while the vacuum pressure head at the throat is 350 mm of mercury. Assuming that 3% of head is lost in between the inlet and throat, find, the value of Cd for the Venturimeter and rate of flow.
In a wastewater treatment plant, Blower supplies air to the sequencing batch reactor. It is necessary to regulate the amount of air being introduced to the reactor and the plant uses pitot static tube meter at the center of flow to measure the maximum flow rate. The manometer shows a difference in head of 75mm.H2O. Determine the maximum air velocity (in m/s, four decimal places). Assume the coefficient of the pitot tube as 0.98. ρair = 1.2 kg/m3, ρwater =1000 kg/m3
Subject: Fluid Mechanics Hydrostatics - please provide complete solution
A liquid having a Reynolds number of 1500 flows thru a 200-mm diameter pipe, 220m long. The head loss of the pipe due to friction is 20m. Determine the following: d. Friction factor. e. Kinematic Viscosity of the Liquid. f. Rate of Flow.
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
m10
blö 8 Question Liquid ( S 1.5) A U-tube differential manometer containing two pipes at A and B. Pipe A contains a liquid of specific gravity 1.5 under a pressure of 100 kPa. Pipe B contains oil of specific gravity 0.8 under a pressure of 350 kPa. Calculate the difference in mercury level (h) in the B differential manometer, as shown in the figure. -Oil (S-0.8) Mercury (S-13.6)
I need hand written solution only
Example -3.12- Two pipes, one carrying toluene of sp.gr. 0.875, and the other carrying water are placed at a difference of level of 2.5 m. the pipes are connected by a U- tube manometer carrying liquid of sp.gr. sp.gr. 0.875 = 1.2. The level of the liquid in the manometer is 3.5 m higher in the right limb than the lower level of toluene in the Water 3.5m 5.0m 1.0 m 2.5m limb of the manometer. Find the B. difference of pressure in the two pipes. Solution: sp.gr. = 1.2
A 150 mm diameter horizontal Venturi meter is installed in a 450-mm diameter water main. The deflection of mercury in the differential manometer connected from the inlet to the throat is 375 mm. (a) Determine the discharge neglecting head lost. (b) Compute the discharge if the head lost from the inlet to the throat is 300 mm of water, and (c) what is the meter coefficient?
Pls answer asap. Thank you
Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is measured using open tubes. If h is 50cm, solve the velocity of flow at Point 1. h O 0.81m/s O 0.88m/s 2.02m/s O 1.29m/s