A fixed control volume has three one-dimensional boundary sections, as shown. The flow within the control volume is steady. The flow properties at each section are tabulated below. Find the rate of change of energy of the system which occupies the control volume at this instant.

A fixed control volume has three one-dimensional boundary sections, as shown. The flow within the control volume is steady. The flow properties at each section are tabulated below. Find the rate of change of energy of the system which occupies the control volume at this instant.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What pressure, p₁, is needed to produce a flowrate of 0.09 ft3/s from the tank shown in the figure below? Assume d = 0.071 ft. P1 = Mi ! psi Air P1 Gasoline diameter d→ Salt water SG = 1.1 2.0 ft 3.6 ft
Q4. Consider simple laminar pressure driven flow in a circular pipe of radius R. We can write the equation for the velocity distribution in the pipe to be: V₂ = 2U|1 2U [1 - (R)²] where U= average velocity. Using the energy equation with the viscous dissipation term, calculate the temperature profile in the fluid due to viscous dissipation alone. Assume that
•Determine the unit weight of the liquid when it is at the level shown. (Express the answer in English unit) •Determine the weight of the liquid. (Express the answer in English unit) •Assuming no mixing of liquids occur, if glycerin (SG= 1.26) is poured into the tank: a.) it will sink to the bottom of the tank b.) it will float on the surface of the liquid c.) it will be suspended in the liquid * answer should be in 3 decimal places
In a steady flow through a nozzle, the flow velocity on the nozzle axis is given by v=uo(1+3x/L), where, x is the distance along the axis of the nozzle from its inlet plane and L is the length of the nozzle. The time required for a fluid particle on the axis to travel from the inlet to the exit plane of the nozzle is (a) L 40 (b) 340 In 4 (c) L 4U0 (d) L 2.500
An orifice meter is a device used to determine the flow velocity and flow rate in a pipe. The meter is connected to a U-tube manometer shown in Figure 2(a). The meter is connected to a U-tube manometer shown in Figure 2(b). Derive the equation for the flow rate, Q in the horizontal pipe.
Argon gas flows through a well-insulated nozzle at steady state. The temperature and velocity at the inlet are 570°R and 150 ft/s, respectively. At the exit, the temperature is 460°R and the pressure is 40 lb/in². The area of the exit is 0.0085 ft². Use the ideal gas model with k = 1.67, and neglect potential energy effects. Determine the velocity at the exit, in ft/s, and the mass flow rate, in lb/s.
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. A 9 ft L = 6 ft d = 1/2 in ܪ e
2. The 600 mm pipe shown in the figure conducts water from a reservoir A to a pressure turbine, which discharge through another 600 mm pipe into water tank B. The head loss from A to 1 is 5 times the velocity head in the pipe and the head loss from 2 to B is 0.2 times the velocity head in the pipe. If the discharge is 700 L/s, what horse power is being given up by the water to the turbine and what are the pressure heads at 1 and 2 2 HE = 49.20 m HP = 453.50 hp (input) P₁/y = 53.63 m P2/y = -4.43 m A WS El 60 m EL 4.5 m 600 mm 600 mm US 90 kPa EL 0 m
Water is pumped from a supply reservoir to a ductile- iron water-transmission line, as shown in Figure 2.26. The high point of the transmission line is at point A, 1 km downstream of the supply reservoir, and the low point of the transmission line is at point B, 1 km downstream of A. If the flow rate through the pipeline is 1 m3/s, the diameter of the pipe is 750 mm, and the pressure at A is to be 350 kPa, then: (a) estimate the head that must be added by the pump; (b) estimate the power supplied by the pump; and (c) calculate the water pressure at B. Supply reservoir Elev. 7 m Pump Elev. 10 m Transmission line Elev. 4 m- B Figure 2.26: Water pumped into a transmission line
What is the mass M that must be suspended at the left to hold the system in equilibrium in the position shown? Please solve this problem please. With FBD and solutions PLEASE.
Ethanol with a density of 789 kg/m moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is P, = 1.90 x 10“ Pa, and the pipe diameter is 7.00 cm. At another point y = 0.35 m higher, the pressure is P, = 1.10 x 104 Pa and the pipe diameter is 3.50 cm. P (a) Find the speed of flow (in m/s) in the lower section. m/s (b) Find the speed of flow (in m/s) in the upper section. m/s (c) Find the volume flow rate (in m/s) through the pipe. |m³/s
A centrifugal pump is used to pump a liquid in steady turbulent flow through a smooth pipe from one tank to another. Develop an expression for the system total head Δh in terms of the static heads on the discharge and suction sides zd and zs respectively, the gas pressures above the tanks on the discharge and suction sides pd and Ps respectively, the liquid density ρ, the liquid dynamic viscosity μ, the gravitational acceleration g, the total equivalent lengths on the discharge and suction sides (∑Le)d and (∑Le)srespectively, and the volumetric flow rate Q.