2- The density of a liquid is to be determined by an old 1-cm-diameter cylindrical hydrometer whose division marks are completely wiped out. The hydrometer is first dropped in water, and the water level is marked. The hydrometer is then dropped into the other liquid, and it is observed that the mark for water has risen S cm above the liquid-air interface. If the height of the original water mark is 12.7 cm, determine the density of the liquid. S(cm)=0.95 Unknown liquid Mark for water Scm

2- The density of a liquid is to be determined by an old 1-cm-diameter cylindrical hydrometer whose division marks are completely wiped out. The hydrometer is first dropped in water, and the water level is marked. The hydrometer is then dropped into the other liquid, and it is observed that the mark for water has risen S cm above the liquid-air interface. If the height of the original water mark is 12.7 cm, determine the density of the liquid. S(cm)=0.95 Unknown liquid Mark for water Scm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate in meters the length of a rectangular settling tank to treat 14,000 cubic meters of water…

Q: The specific gravities of solids and carrier fluids of a slurry are usually known, but the specific…

A: Specific gravity is defined as the ratio of the density of solids in the slurry and the density of…

Q: 1. A water sample is known to contain 300 g/m3 of casein (C8H12O3N2). Estimate the COD, BODu, and…

A: Given data: Mass of sample of casein m=300 gm/m3 Deoxygenating Constant at temperature 20°C=…

Q: Figure shows a container filled with light oil and heavy oil. The masses of two types of oil are the…

Q: need the answer

Q: working from first principles develop the D'Arcy equation for the head loss in a pipeline.

A: Darcy Weisbach equation or Darcy's equation is named after two scientists Henry Darcy and Julius…

Q: A very small drop of fluid 1 immersed in fluid 2 is sitting on a solid surface. Based on the image…

A: A contact angle less than 90 indicates wetting liquid or hydrophilic liquid and lower density as…

Q: fluids shown in the figure are at 20°C. If V₁ = 2.6 ft/s and losses are neglected, determine the…

A: This question is related to the Fluid Mechanics from Civil Engineering. Given Data - V1 = 2.6…

Q: 1. In Figure below, sensor A reads 3.5 kPa (gage). All fluids are at 15°C. Determine the elevations…

A: PA=3.5kPa

Q: Calculate the required diameter.

A: The values and diagram given in the question are as follows: The difference between points 1 and 2…

Q: I. Explain How to determine the fuid properties of these liquids in the laboratory by applying…

Q: 2) From the figure shown below determine how many minutes would it take for the water surface in…

Q: A wooden block (40 cm wide (b), 20 cm long (h) and 15 cm deep) floats on the seawater (specific…

A: Find center of gravityCG=152=7.5cmFind center of BuoyancyCB=122=6cm from bottom

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: Reference : Fluid mechanics, Pressure analysis for Volatile liquid. We know that , Gage pressure is…

Q: An clectrostatic precipitator is being designed to operate at an efficiency of 97%. Using the…

Q: Question 3 a) Consider the water container with a conical plug at the bottom, as shown. Determine…

Q: Current Attempt in Progress A sound wave is observed to travel through a liquid with a speed of 1250…

A: Given: Velocity of sound wave in fluid Specific gravity of fluid To find: Bulk modulus of fluid…

Q: The reading of an automobile fuel gage is proportional to the gage pressure at the botoom of the…

Q: A venturi meter equipped with a differential mercury manometer as shown in Figure 1. At the inlet,…

A: Venturimeter is a device which a type of flowmeter which works on Bernoulli's principle. It is…

Q: Use Euler's method to solve for the depth y

A: Euler's method to calculate the depth from t=0 to t=10d with a step size of .5dh is the step sizen…

Q: The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid…

A: Let Point A at the surface of liquid & Point B at 1m below the surface of liquid. Given density…

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

Q: 3. In Figure below, sensor A reads 2.5 kPa (gage). All fluids are at 10°C. Determine the elevations…

Q: A tank initially contains 100 gallons of brine in which there is dissolved 20 lb of salt. Starting…

Q: As shown in Figure 1, an ideal gas flows isentropically from a large tank into a converging ozzle…

Q: (5) As shown in the image, an air space above a long tube is pressurized to 50 kPa vacuum. Water…

A: Given Initial Pressure in air space=50 kpa Final Pressure in air space=25 kpa Assume Atmospheric…

Concept explainers

Pressure and Stress

Question

2- The density of a liquid is to be determined by an old 1-cm-diameter cylindrical hydrometer
whose division marks are completely wiped out. The hydrometer is first dropped in water, and
the water level is marked. The hydrometer is then dropped into the other liquid, and it is
observed that the mark for water has risen S cm above the liquid-air interface. If the height of
the original water mark is 12.7 cm, determine the density of the liquid.
S(cm)=0.95
Unknown
liquid
Mark for
water
Scm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the manometer in the figure, determine the difference in gage pressures between points A and B
Show complete solution Fluid Mechanics
Illustrate the diagram
For part B) need good explanation.
Find the depth of the water in the tank, H, and the manometer reading, h, if the hydrostatic force on the circular plug is 25 N. Take the specific weight of the water as γwater = 9810 N/m3 and the specific gravity of mercury Sm = 13.56
Provide solution for each answer
(c) Consider the following conditions: Condition 1 Condition 2 A wooden cube of size 2 m and the 20% of the volume of a body is visible relative density of 0.5 floats in the over the free surface of the water. water. Calculate: (i) Volume of the cube submerged in the water, based on Condition 1. (ii) Density of the wooden cube, based on Condition 2.
Solve and Draw the figure completely labelled with all the notations used in your solution.A fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose, terminating in a 25 mm nozzle. The nozzle is 3 m above the hydrant and 18 m above the pump. Assuming a total frictional loss of 18.5 m from the pump to the base of the nozzle, and a loss in the nozzle of 10 per cent of the velocity head in the jet, and neglecting air resistance, what gage pressure at the pump is necessary to throw a stream 30 m vertically above the nozzle?
In the inclined manometer shown in the figure below, the reservoir is large. Its surface may be assumed to remain at a fixed elevation. A is connected to a gas pipeline and the deflection noted on the inclined glass tube is 100 mm. Assuming q = 30° and the manometric fluid as oil with specific gravity of 0.86, the pressure at A is A 100 mm Ꮎ B
The discharge through a 75mm diameter orifice at the bottom of a large tank was measured to be 1734 liters for every minute. If the head over the orifice remains constant at 5.5m, determine the coefficient of discharge. (A 0.91 В 0.63 0.84 No Answer among the choices (E) 0.72
Read the question carefully and give me right solution according to the question.
28. The tank shown in figure below is closed at top and contains air at a pressure at top and contains air at a pressure of P. The value of Pfor the manometer readings shown will be X- Open tube 200 cm 10 cm T © Air - X 4 A Oil RD = 0.75 Water T 150 cm