A three-fluid system (immiscible) isconnected to a vacuum pump. Thespecific gravity values of the fluids(S,, S,) are given in the figure.To vacuum pumpP.S, = 0.88Fluid I1 1.5 mP 1 1.0 m0.5 mPmS, = 0.95Fluid IIFluid III : WaterUnit weight of water, Y. =9.81KN/m³Atmospheric pressure, Pam = 95.43kPaThe gauge pressure value (in kN/m²) upto two decimal places of p, is

Answered: Image /qna-images/answer/74e10f38-40f1-44a4-a4ae-45ebceb90d45.jpg

A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S,, S2) are given in the figure. To vacuum pump Pi S, = 0.88 Fluid I S, = 0.95 Fluid II 1.5m P-1 1.0 m 0.5 m P Fluid III : Water Unit weight of water, Y. =9.81KN/m³ Atmospheric pressure, Pm =95.43kPa The gauge pressure value (in kN/m²) up to two decimal places of p, is

A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S,, S2) are given in the figure. To vacuum pump Pi S, = 0.88 Fluid I S, = 0.95 Fluid II 1.5m P-1 1.0 m 0.5 m P Fluid III : Water Unit weight of water, Y. =9.81KN/m³ Atmospheric pressure, Pm =95.43kPa The gauge pressure value (in kN/m²) up to two decimal places of p, is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

28. The tank shown in figure below is closed at top and contains air at a pressure at top and contains air at a pressure of P. The value of Pfor the manometer readings shown will be X- Open tube 200 cm 10 cm T © Air - X 4 A Oil RD = 0.75 Water T 150 cm
How to solve this question . Step-by step solution needed with explanation. ( Fill in the Blank)
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. A 9 ft L = 6 ft d = 1/2 in ܪ e
M27
Given The tank shown has one curved surface restraining a body of static fluid, with the following dimensions: w- 5.00 m h1 = 2.5 m R1 = 0.85 m Required Determine the value of x-bar in metres, to the nearest 1000th. Water hl R1
For many applications, it is accurate enough to treat water as incompressible. But for a more detailed understanding of fluid flows, compressibility must be taken into account. Fortunately, the bulk modulus of water is close to constant, so let's model the pressure in a motionless water column assuming that the bulk modulus is a constant, K, = 2.1 GPa. The pressure and density at the top surface of the water column are 6. Po =1000 hPa and P, =1000 kg/m², respectively, and the downward acceleration due to gravity is g =9.8 m/s. Take depth, z, to be positive downward with z = 0 at the top %3D %3D %3D surface. Using the definition of bulk modulus, derive an expression for the density field, p, in terms of pressure, p, and the given parameters. Leave all parameters а. as algebraic. (At this point, your expression should not include z .) b. Starting from hydrostatic balance and the expression in part (a), derive an expression for the pressure field, p(z), in terms of z and the given…
The Newtonian fluid shown in is confined between the plate and a fixed surface as shown in (Figure 1). Its velocity profile is defined by u = (8y-0.3y2) mm/s, where y is in mm. The plate has a surface area of 29(10³) mm² in contact with the fluid. Take μ = 0.482 N. s/m². Suppose that h = 6 mm. Figure h < 1 of 1 Part A Determine the force P that must be applied to the plate to cause this motion. Express your answer to three significant figures and include the appropriate units. xa P= 67.1 μA Xb a b X.10n < Return to Assignment mN Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ? Provide Feedback
Q 1 A
IV. Water is discharged from a device in to air, as shown in the figure. How much is the horizontal force to hold the device. Ignore gravity and viscosity. 1 Ibf= 1 slug ft/s 2, air (2)A=0.4 t 30 fU 10 psi Flang 1/20 tis (1) A=0.8 (E) A- 0.8 n air Water density =1.94 slugs/ft^3.
Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the center of the pipe; the reading of a mercury manometer connected to the pitot is 100 mm. The flow is also measured by a venturi meter which connected with the same mercury manometer and the pressure drop across it equals to 300 mm. Find the ratio of venturi to pipe diameter and determine the pressure drop due to friction across the venturi meter.
Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter (cm) Length (m) Friction factor 1 15 500 0,02 2 10 450 0.03 3 20 800 0,025 3. Determine the flow in pipe 3.
A centrifugal pump is used to pump a liquid in steady turbulent flow through a smooth pipe from one tank to another. Develop an expression for the system total head Δh in terms of the static heads on the discharge and suction sides zd and zs respectively, the gas pressures above the tanks on the discharge and suction sides pd and Ps respectively, the liquid density ρ, the liquid dynamic viscosity μ, the gravitational acceleration g, the total equivalent lengths on the discharge and suction sides (∑Le)d and (∑Le)srespectively, and the volumetric flow rate Q.