Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the center of the pipe; the reading of a mercury manometer connected to the pitot is 100 mm. The flow is also measured by a venturi meter which connected with the same mercury manometer and the pressure drop across it equals to 300 mm. Find the ratio of venturi to pipe diameter and determine the pressure drop due to friction across the venturi meter.

Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the center of the pipe; the reading of a mercury manometer connected to the pitot is 100 mm. The flow is also measured by a venturi meter which connected with the same mercury manometer and the pressure drop across it equals to 300 mm. Find the ratio of venturi to pipe diameter and determine the pressure drop due to friction across the venturi meter.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
A differential manometer is attached to a pipe shown. Calculate the pressure difference between points A and B.
blö 8 Question Liquid ( S 1.5) A U-tube differential manometer containing two pipes at A and B. Pipe A contains a liquid of specific gravity 1.5 under a pressure of 100 kPa. Pipe B contains oil of specific gravity 0.8 under a pressure of 350 kPa. Calculate the difference in mercury level (h) in the B differential manometer, as shown in the figure. -Oil (S-0.8) Mercury (S-13.6)
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
In the following manometer set-up, d, is measured to be 10 in, dz measures 4 in, d; measures 14 in, da measures 3 in. If SGmercury is 13.55, a) calculate the pressure difference (in psi) between points A and B b) if the pressure at B is 15 psi, what is the pressure at A? Water- -Mercury
FLUID MECHANICS
(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5
dear eng ans quickly
A manometer is attached to a conduit as shown. What is the pressure at A in kPa. Choices are: A. 38.25 kPa B. 38.85 kPa C. 32.85 kPa D. 38.45 kPa
Question 1 b) The U-tube manometer can be used to detemine pressure difference between two systems. This type of manometer is called a differential U-tube manometer. Consider the differential manometer connected to a pipe, as shown in Figure 1. Explain step by step on how you can calculate the pressure difference between point A and B. P1 h, A Flow Test Section U-Tube Differential Manometer
6- Determine the absolute pressure in a pipe which is connected to a simple U-tube manometer, the pipe contain a liquid with a relative density 0.7, the height of the liquid in the manometer limb is 0.2 m, and the height of mercury in the other limb is twice as height of liquid.
For the manometer set up shown, determine the difference in pressure between A and B.