The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid and its vapor. The liquid density is 800 kg/m³, and its vapor density is negligible. The pressure in the vapor is 149 kPa (abs), and the atmospheric pressure is 101 kPa (abs). Determine (a) the gage pressure reading on the pressure gage and (b) the height, h, of the mercury manometer. (a) (b) Pgage= h = m 1m 1m Į kPa Vapor Liquid Open Mercury

The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid and its vapor. The liquid density is 800 kg/m³, and its vapor density is negligible. The pressure in the vapor is 149 kPa (abs), and the atmospheric pressure is 101 kPa (abs). Determine (a) the gage pressure reading on the pressure gage and (b) the height, h, of the mercury manometer. (a) (b) Pgage= h = m 1m 1m Į kPa Vapor Liquid Open Mercury

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please help me part 2
The cyclindrical tank with hemispherical ends shown in the figure below contains a volatile liquid and its vapor. The liquid density is 800 kg/m³, and its vapor density is negligible. The pressure in the vapor is 124 kPa (abs), and the atmospheric pressure is 101 kPa (abs). Determine (a) the gage pressure reading on the pressure gage and (b) the height, h, of the mercury manometer. (a) Pgage (b) h= 3 1 1m 1m kPa Vapor Liquid 1 m Open Mercury
Figure 1 shows the manometer apparatus with different fluids. It is given that the specific density of the mercury and oil are 13.56, and 0.9 respectively. Solve, a. The liquid level, Az when the area of the reservoir on the left limb of the manometer is 100 times the area of the manometer tube in right limb. The volume X is equal to Volume Y. b. The pressure at point A. Oil Volume Y 45cm 18cm Mercury Az Volume X Figure 1 ץחרים
I need the answer as soon as possible
Solve this fast response..
Fluid فورم قديم
1. Describe the basic principles of dilatometer testing. 2. List the main component in dilatometer instruments ( 3. Derived the formula for coefficient of thermal expansion ( 4. Demonstrate how CTE can be measured from dilatometric curve Part 2: CO4 5. Give short description for each given Figure: ( 1.0- Parent glass Glass-ceramic 0.8 S0.6- 0.4- 0.2- 0.0- 200 400 600 800 Temperature (C) Figure 1: Dilatometric curve of parent glass and glass-ceramic sample 0.008 40Z60A 50Z50A 60Z40A 80Z70A 0.007 0.006 0.005 0.004 0.003 0.002 0.001 200 400 600 800 1000 1200 1400 Temperature (°C) Figure 2: Dilatometric curves for each sintered sample, containing different zircon- alumina weight proportions (%) '7/7P dL/Lo*10-6
Can you please explain step by step how the final answer was obtained? Tried it out myself & don't know how they ended up getting the answer , please help!
A 0.6 m square glass plate slides on a plane with a slope of 30° from the horizontal (Figure 1.2). Knowing that the plate weighs 30 N and that it acquires a constant speed of 5 cm/s, it is asked: determine the dynamic viscosity of the film 0.1 mm lubricant, which is between the plates. Assume the velocity diagram linear in the fluid film). (R: 0.0833 Ns/m2) 5cm/s Figure 1.2 0.1 mm
2. Determine the pressure difference (pM – pv) when the manometer indicates as shown below. (38.690 kPa) Ol of RD-0.0 15 am 20 am IT 12 cm 16 om Mercury
A pipe contains an oil of specific gravity 0.9. A differential manometer connected at the two points A and B shows a difference in mercury levels as 15 cm. The difference of pressure at the two points A and B will be (Note: consider the density of mercury as 13600 kg/m-). O 18688 N/m2 O 15981 N/m2 O 288 N/m2 O6528 N/m2
Trichlorethylene (SG = 1.466), flowing through both pipes, is to be added to jet fuel produced in a refinery. A careful monitoring of pressure is required with the inclined-tube manometer. Manometer fluid is mercury (C to D). If the pressure at A is 30 psi and at B is 25 psi, determine the position ‘s’ in inches) that defines the level of mercury in the inclined-tube manometer. Use x = 18 in., y = 14 in., z = 12 in. a. 9.286 b. 3.552 c. 14.892 d. 7.986