Can you please help me with this answers are already provided please show detailed solution thank you!The U-tube in the figure is given a uniform acceleration of 1.22 m/s to the right. What is the depth in AB and the pressures at B, G and D? The U-tube in the figure is given a uniformacceleration of 1.22 m/s to the right. What is thedepth in AB and the pressures at B, G and D?AmercuryH30 cmGDB30 cm30 сmFIGURE HHAnswers:34 cm ; 45.36 KPa ; 40 KPa ; 34.70 KPa

Answered: Image /qna-images/answer/677ad6d4-2156-486b-8c1f-c8088e547bc7.jpg

The U-tube in the figure is given a uniform acceleration of 1.22 m/s to the right. What is the depth in AB and the pressures at B, G and D? A mercury H C 30 cm G D B 30 cm 30 сm FIGURE HH Answers: 34 cm ; 45.36 KPa ; 40 KPa ; 34.70 KPa

The U-tube in the figure is given a uniform acceleration of 1.22 m/s to the right. What is the depth in AB and the pressures at B, G and D? A mercury H C 30 cm G D B 30 cm 30 сm FIGURE HH Answers: 34 cm ; 45.36 KPa ; 40 KPa ; 34.70 KPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the magnitude of the resultant force on the indicated area and the location of the center pressure. Show the resultant force on the area and clearly dimension its location. From the figure
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
A newtonian fluid flows down an infinitely long cyalindrical tube (as shown in the figure below). There is NO applied pressure gradient, and fluid flows down the pipe due to gravity alone.i) Derive the velocity profile (?(?) =?). ii)Find???? ,???iii) Draw the velocity and shear stress profiles, showing the points where ? or ? is equal to zero or at their maximum value.
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1m Liquid (s.g. = 0.88 ) 4 m B 2.6 m 1 m 幸 +
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
The tank shown in figure is fabricated from 0.125-in steel plate. Calculate the maximum circumferential stress in psi caused by an internal pressure of 142 psi. a = 1.8 ft. and b = 3.0 ft.
Hi, I need help with this question please. Thank you. A cantilever thin-walled cylindrical tube of inner diameter ? = 30cm and thickness ? = 1cm is subjected to a torque T and internal pressure p as shown below. The free end of the tube is closed. Strain gauges A and B mounted on the surface of the cylinder give readings ?? = 7.5 × 10^−6 and ?b = 19.7x10^−6, respectively. The bar is made of steel having Young's modulus E=200 GPa and Poisson's ration ? = 0.3. a) Determine the torque, T, and internal pressure, p. b) Determine the absolute maximum shear strain ???? at point C.
Fluid flows past the two dimensional bar shown in figure. The pressures on the ends of the bar are as shown, and the average shear stress on the top and bottom of the bar is tavg. Assume that the drag due to pressure is equal to the drag due to viscous effects, the ratio between the average shear stress and the dynamic pressure is p = -0.2 U Width =b Tave -10h
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
In the figure below, the beam is cantilevered from the wall. The connection of the beam to the wall can be considered a general interaction. The beam has a uniform density, so it will be subject to a weight force applied mid-way between points A and B. length from point A to point B =10.0 meters; weight applied at point B = 1.00 kN; beam weight = 0.500 kN Beam embeded in cwalla cautilever B A What is the magnitude and direction (relative to the x-y coordinate system shown in the upper left portion of the figure) of the horizontal and vertical components of the wall support? horizontal = 0 N, vertical = 1.50 kN O horizontal = 1.50 kN, vertical = 0N O horizonatl = O N, vertical = 1.00 kN O horizontal = ON, verttical = 2.00 kN