Hydrostatic Force - Pressure x Area Suppose that a vertical, parabol1ic gate is installed on the side of a 24 ft deep gas tank. The shape of the gate is defined by the equation y=2-r, so that y=0 coincides with the bottom edge of the tank (units in feet). * the gate was designed to withatand a maximum force of 6,000 lbs , verify the gate will not break when the tank is filled with gas. Ibs The weight density of gas is 44-

Hydrostatic Force - Pressure x Area Suppose that a vertical, parabol1ic gate is installed on the side of a 24 ft deep gas tank. The shape of the gate is defined by the equation y=2-r, so that y=0 coincides with the bottom edge of the tank (units in feet). * the gate was designed to withatand a maximum force of 6,000 lbs , verify the gate will not break when the tank is filled with gas. Ibs The weight density of gas is 44-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical gate (ad) is shown in flgure. Determine the force F' per meter width of the gate to keep it closed. 3 m di Hinge R= 5m
The tank with hexagonal cross-section shown is fabricated from 1/8-in steel plate. Calculate the maximum hoop and longitudinal stress along the thickness caused by an internal pressure of 130 psi. How much bursting force is developed along the longitudinal section when the length of the tank is 5 ft?
A vat full of paint (SG = 0.80) is 8 m long and 4 m deep and has a trapezoidal cross section 3 m wide at the bottom and 5 m wide at the top as shown. a. Compute the force on the bottom of the vat. b. Compute the force on the trapezoidal end panel. c. Compute the weight of the paint. Unit of the Correct Answer: kN Decimal Places required in the final answer: 3
The gate AB is a quarter circle of 2.5 meters in diameters and 3 meters wide asshown in figure#2. How Find the horizontal component of the resultant hydrostatic forceacting on the gate in kilonewtons. How find the vertical component of the resultant hydrostatic force actingon the gate in kilonewtons, and how to find the location of PH and Pv from hinge A in meters. And if the weight of the gate is 100 Newtons, how find the force “F” just sufficient to preventrotation about hinge A.
The gate holding back the oil (S=0.8) is 80 cm high and 120 cm long. If it is held in place only along the bottom edge, what is the magnitude of the force that must be applied at the bottom to keep the gate closed? binge- 40 cm 80 cm gate Select one: O a. 3.52 kN O b. 4.40 kN O c. 3.01 kN O d. 4.68 kN
Compute the reaction at hinge B the given figure below. Express your answers in lb. The values of a, b, and y are 7.4, 10.5, 20 ft, respectively. The gate is 5 ft wide. y 'ft Hinge Patm Seawater: Y=64 lb/ft³ Gate b ft- a ft Wall Patm
Consider the tank shown in the figure. The gate is rectangular in shape with width into the paper of 2.0ft. Given: h=4.1ft B=4.2ft Angle,sg= 0.70 Calculate the eccentricity(inches) of the hydrostatic force on the gate.
Determine the moment of inertia of the cross-sectional area of the reinforced channel about the x-axis. Assume t = 1.0 in., a = 1.8 in., b = 1.6 in., c = 2.2 in. 一一叫 F₁-a- Answer: lx = i in.4 x
Question 2 Determine the support reactions for the system shown, given the force P and distributed load w noted below. All dimensions are in millimetres (mm). W B 2400 3000 4000 1000 Question 2 . P- 10 kN W= 5 kN RAY kN (0 decimal places) RET kN (0 decimal plaçes) Rox AKN (0 decimal plaees) Rpy kN (0 decimal places)
A transmission tower shown below is subjected to lateral loads as shown. A =3.6 kN, B =4.1 kN, C =8.1 kN Determine the magnitude of the axial force in member GK. Answer in 2-decimal places only if applicable, and don't include units. A-KN 1.5 m 1.8 m B-kN H/ AG 1.8 m C-kN E F. 1.8 m B. 林2.55 m C. 2.55 m
Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,