Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. 9 ft L=6 ft d=in B Q

Q: Question 240K-ft where E = 1800 kst H=13,432 int 24 Ft Cal culate andl draw the de formed Shafe.…

A: Given  E = 1800 ksi  I= 18432 in 4

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 890 MPa…

A:

Q: a. Compute the bulk modulus of elasticity. b. Compute the percentage of volume decreas c. Compute…

A:

Q: 1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: A stress element is given with stresses shown. Young's modulus of elasticity, E = 80GPa Possion's…

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 704 MPa…

A:

Q: Question: A rectangular column is shown in the figure, assuming fc'=28Mpa, fy=345Mpa, and e=110mm,…

A: Eccentricity, Width of section, Depth,

Q: A rigid horizontal slab is attached to two identical copper rods. There is a gap, A = 0.18 mm…

A: Given data,

Q: For any given velocity of flow, the friction factor "f" O will decrease as the diameter of the pipe…

A:

Q: A thin, homogeneous disk of mass m and radius r spins at the constant rate Vị about an axle held by…

A: Consider the figure,

Q: Stress analysis Task Question / Calculate the critical design loads applied to the Stirling Engine…

A: Please find the answer in the below attachments

Q: Water Steel block 250 mm b. Mercury (s.g. = 13.6)

A: answer = 297.82 mm

Q: A cantilever beam with a 'T' shaped cross-section is loaded with a distributed load as shown below.…

A: Width of flange= 80 mm  Height of web = 75 mm

Q: Problem 4.100 Replace the force system acting on the beam by an equivalent force and couple moment…

A:

Q: Given: • Rod A: Length = 40mm Rod B: Length = 60mm Determine: ● ● Area = 3 cm x 3 cm Area = 4 cm x 4…

A: Given data  P = 100 KN  EA = EB = 200 GPA = 200 × 103 N/mm2    Area of rod-A (AA) = 3cm × 3cm = 30mm…

Q: H.S An open cylinder can has an inside radius of 2 cm and an inside height of 5 cm use the total…

A:

Q: SITUATION. A steel pipe of internal diameter 799 mm and of thickness 2 mm has to be slipped on to a…

A:

Q: The cross-sectional dimensions of a beam are shown. a) If the bending stress at point K is 2810 psi…

A: Given :

Q: The rod shown with segment made of steel and copper experienced a 50°C raised in temperature.…

A: Given data: αst=11.7×10-6 m/m∘Cαcu=21.6×10-6 m/m∘CEst=200 GPaEcu=70 GPaT=50∘C

Q: The shown circular bar is fixed to the left wall. It has a diameter of 0.5 in and length of 60 in at…

A: for having stress free of right wall, bar should be elongated maximum equal to the gap.

Q: Situation H. A 100m tape weighing 3kg that is standard at 10°C and a 30N pull is used to measure a…

A: Length of tape = 100m Weight of tape = 3kg Standard temperature = 10°C Measured length of Tape =…

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

A: Given-a rod subjected to a tensile load of 300N Required- to find change in length, diameter, volume…

Q: The wood block in (Figure 1) has a specific weight of 45 lb/ft³ = 62.4 lb/ft³. Take Po = 1.75…

A: Given data:Specific weight of wood block= 45lb/ft3Width of block =1 ft

Q: Modulus of elasticity, modulus of rigidity, and Poisson's ratio are interrelated. (a) Calculate G…

A:

Q: Solid shaft AB rotates at 480 rpm and transmits 30 kW from the motor to gears G and H; 20 kW is…

A: For the given conditions, the minimum possible diameter of the shaft has to be determined

Q: a

A: Given  open cylindrical tank, with diameter d= 605 mm  thickness t = 3.02 mm a= 40.10 MPa, b =…

Q: Please create the pressure profile in excel ( graph ) Just like the example on the picThank you

A:

Q: ne the volume V and total surface area A of the solid z k 63 mm 43 mm *

A:

Q: 1  Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in Figure Q1 (a), can…

A:

Q: TWO CONCRETE BLOCKS WEIGHING 1800 N EACH FORM PART OF THE RETAINING WALL OF A SWIMMING POOL. WILL…

A: Given:   Weight of each block    =1800 N Friction coefficient at the base of the first block,…

Q: I was wondering in the hydrodynamics how i can determine Cp in the pressure ressistance (coefficient…

A: In the context of total resistance, the coefficient of drag (Cd) is a dimensionless quantity that…

Q: tape was unilormly supported during the measurement. Find the true length of the line f the cross…

A:

Q: Two concrete blocks weighing 1800N each form part of the retaining wall of a swimming pool. Will the…

A: Draw the free body diagram From the above diagram R1=12×6Nmm×5401080×540R1=810N

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 400 N is applied…

A:

Q: A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the…

A:

Q: A rigid slab weighing 600 ku is placed upon t ·bronze rods and one Steel rod each of 6000 mm² area a…

A: This question is related to the Strength of Material.

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.