A vinyl [E = 2.90 GPa; v = 0.41] block with width b = 40 mm, depth d = 80 mm, and height h = 210 mm rests on a smooth rigid base. A load Pis applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P = 60 KN is applied.

A vinyl [E = 2.90 GPa; v = 0.41] block with width b = 40 mm, depth d = 80 mm, and height h = 210 mm rests on a smooth rigid base. A load Pis applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P = 60 KN is applied.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: (Bernoulli/continuity) Water flows steadily through a diverging tube as shown in the figure below.…

A: Given data: d1=0.52 ftd2=0.70 ftd3=0.92 ftSG=2y=2.4 ft

Q: 4. Find the dimensions of a concrete lined open channel used to convey a discharge of 70 m/s. The…

A: Given data Discharge Mannings roughness coefficient Side slope Bed slope

Q: 20 IN H 1=3 m 3 d 1=3 m 1-3 m Which of the following most nearly gives the force in member cd due to…

Q: Calculate the equivalent concentrated force of distributed force diagram, draw the free body diagram…

A: Consider the free body diagram of the beam,

Q: Problem 13. In a stream line steady flow, two points A and B on a stream line are 1 m apart and the…

Q: 1. Find the center of gravity of a semicircular section having outer and inner diameters of 200 mm…

Q: Answer in whole number w C A x В L- L/2

Q: 4. A 5/8-in-diameter steel rod AB fitted to a round hole near end Cof the wooden member CD. A…

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

Q: 5. Segment AB of the bar is a tube with an outer diameter of di and a wall thíckness of 0.125 in.…

A: To Find:- Diameter d1 Diameter d2

Q: Situation 4. Determine the Centroid of the configuration of the steel sections below. Also determine…

Q: Part 8

A: Data given Load P = 250 kN Modulus of Elasticity of Steel, Es = 200 ×106 kN/m2 Modulus of…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Finding out twist developed in steel from support B.

Q: A column is supported on a footing as shown in the figure below. The water table is at a depth of 10…

A: Given- Water table at a depth of 10 m, Size of footing- 1.5 m × 3 m, Depth of footing Df=1 m, Unit…

Q: Find the axial stress (in psi) of the steel. " Your answer Find the axial stress (in psi) of the…

Q: Which of the following is the equation of the deflection curve at segment AB? P kN/m В A 000 2 O…

Q: From the given beam loaded has shown; Ely = RA2² – M, (x – ) + C1, Ely = ¿RA2³ – M, (x – )² + C,x+…

A: Given data As the beam is a propped cantilever there are 3 boundary conditions At fixed support…

Q: t www h. The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa, Ib Ic=…

Q: the given figure: Let P = 26kN, L = 8m, a = 3m %3D equation of the slope is EIy = Pa (-+L),…

Q: From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m. PKN L/3 m QkN/m Lm Determine the following;…

Q: 6. A biodegradable fuel having a specific gravity of 0.95 and a viscosity of 0.04 grams per cen-…

A: Solution (6) Reynolds number of the biodegradable fuel is calculated by. Re =ρvDμv =Re ×μρD Where, ρ…

Q: Ias 글 RAz2-Mo (z-블〉 + Ci, Ely = Mo B –L/2- -L/2– = 59kNm. L = 12m ine the EI0 at point A

Q: 13-5. Air pressure in the cylinder is increased by exerting forces P= 2 kN on the two pistons, each…

A: The solution for Question No 13-5 is as follows: Given Data: The air pressure in the cylinder is P=2…

Q: 11. What is the significance of the number of the sieves? To be precise, what does 200 mean in # 200…

Q: Calculate moment reaction at support A

A: Given: Cantilever beam with following loading condition To calculate: Moment reaction at A, Ma

Q: 1. Find the center of gravity of a semicircular section having outer and inner diameters of 200 mm…

Q: Form the given beam loaded has shown, Ely = MAr + RA2² – ¿P(x – )² + C1 Elf = }Max² + ¿RAr – P(r –…

Q: 4. A trapezoidal channel of bed width 8.0 m, side slopes are 1:1, longitudinal bed slope = 12 cm/Km,…

Q: 3. From the figure, AB is connected by a hinge at A. It is supported by a rod CD at C. The rod is…

Q: 24 m^4

Q: Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while…

Q: 6. A cylindrical sample of soil is iso-tropically compressed at 150 KPa under drained condition.…

A: A sample is compressed at 150 kpa at under drained condition and change in radial stress 300 kpa and…

Q: 2. Show an example of the design process of an actual finished structure (The structure does not…

A: Introduction- It translates the client's or occupant's requirements, demands, and ideas into a…

Q: A basin has an area of 400 km² and the following characteristics: L = Basin length = 35 km Le =…

Q: A tube is used as shaft wherein 90 kW of power is transmitted. If its outer and inner diameter are…

A: To find the frequency-

Q: A dam 6m on top, 12m at the bottom and 20m high has water 15m depth acting on its vertical side. 2.…

A: Given top = 6m bottom = 12 m height = 20m depth of water = 15m here I was taking calculations…

Q: View Policies Current Attempt in Progress A flow rate measuring device is installed in a horizontal…

A: Determine the differential reading of the manometer corresponding to a pressure drop between the…

Q: From the given figure: Let P = 55kips, L = 16ft, a = 6ft if the equation of the slope is EIf =…

Q: 2. Draw the FBD. Find the support reactions in A and tension force in the cable. P =8 KN. 0.5m 0.75m…

A: In question number 2, we have to find forces and tension in rigid body and rope respectively by…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

100%

A vinyl [E = 2.90 GPa; v = 0.41] block with width
b = 40 mm, depth d = 80 mm, and height h = 210
mm rests on a smooth rigid base. A load Pis
applied to a rigid plate that rests on top of the
block. Calculate the change in the depth
dimension d of the block after a load of P = 60
KN is applied.
Answer:
Δd =
Rigid
plate
mm
Width
b
Depth
d
Height
h
Rigid base

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

How to make a effective stiffness matrix for this figure?
The rectangular plate is deformed into the shape shown by the dashed lines. Calculate the average normal strain along diagonal AC. and The average shear strain at corner A relative to the x,y axes.
PROBLEM 37: A sieel secion havung a Cioss seciion c: 20 mm x 30 mm is subjected to an axial force of 240 KN The steel section has produces a strain of 0.002. If it has a value of Poissons ratio of 0.30.Find the shear modulus a. 76923 MPa b. 73852 MPa C. 78023 MPa d. 80256 MPa
A) Determine the lateral strain B) Determine the axial strain C) determine the poisson’ts ratio V. COMPLETE SOLUTION. THANKS!
Compute for the adjusted reference compressive stress with modifications, ( Fc* ) in MPa
Two planks of different materials are attached by a special glue as shown in the figure. Theplanks have equal widths which is equivalent to 200mm. The thickness of the planks is50mm each. Determine the normal stress acting on the wooden plank and theshearing stress of the glued area if a tensile force of 20kN is applied at both ends.
A vinyl [E = 2.80 GPa; v = 0.43] block with width b = 40 mm, depth d = 80 mm, and height h = 210 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P = 60 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
In a standard tensile test a steel rod of 22-mm diameter is sub- jected to a tension force of 75 kN. Knowing that v = 0.3 and E = 200 GPa, determine (a) the elongation of the rod in a 200-mm gage length, (b) the change in diameter of the rod. 0 60 9:59 3/12/2
A line is inscribed on a 3 mm thick steel alloy plate with an elastic modulus E = 200 GPa and shear modulus G = 70 GPa. The plate is then loaded as shown below. 2a) Determine the slope of the line after the plate has been loaded 2b) Determine the reduction in thickness of the plate (in mm) under the applied loads 2c) If the plate has a yield stress = 300 MPa, determine the factor of safety against failure according to the Maximum Normal Strain (St. Venant's) Criterion Steel Alloy Plate: y line 250 mm k Į 50 kN 70 mm ↑ 70 mm 100 KN 125 mm
5
A 31 mm diameter bronze bar 3.7 m long is placed between two rigid walls. At a temperature of -39°C, the gap A = 2.3 mm. Find the temperature(at degree-Celsius) at which the compressive stress in the bar will be 40 MPa. Use a = 19.84 x 106 m/(m-°C) and E = 82 GPa. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution.