20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the final thickness. Provide the answer in mm a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm σ = 160 MPa

20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa and Poisson's ratio is 0.35. If the initial thickness of the plate is 5mm. Determine the final thickness. Provide the answer in mm a with two decimal points of accuracy. σ = 80 MPa 20 mm Answer: D 20 mm σ = 160 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QUESTION 2 The bar shown has a cross-sectional area of A Young's modulus of E and a length of L. It is carrying a force of F. Calculate the normal stress (a) in the bar. F F O k Your unique values to use are (everybody will get different values for every question): 45 KN 4256 mm A 426 mm² 220 GPa Your mark will be based entirely on the answer you select from below. 0 = 233 MPa o=151 MPa 0=171 MPa = 190 MPa a=202 MPa a = 92 MPa 0 52 MPa 0122 MPa 0=76 MPa 0= 145 MPa 0-62 MPa o=140 MPa d=212 MPa 0106 MPa 0-100 MPa
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following:a. Stress in the bronze segment.b. Stress in the aluminum segment.c. Stress in the steel segment.
Please answer it properly don't waste my question I will vote it up for your effort thank you.
1.5-6 The data shown in the table were obtained from a tensile test of a metal specimen with a diameter of 0.500 inch and a gage length (the length over which the elongation is measured) of 2.00 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Use the slope of the best-fit line to estimate the modulus of elasticity. Load (kips) PI223 SIN 0 2.5 3.5 10 11.5 12 Elongation (in.) 0 0.0010 0.0014 0.0020 0.0024 0.0036 0.0044 0.0050 0.0060 0.0070 0.0080 0.0120 0.0180
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 12Q°C. The 0.5-mm gap exists at 2T°C.
Hi, can you answer quickly please
A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 3000 N. If the stress is not to exceed 150 MPa at -20°C, find the resulting stress in MPa due to change in temperature. Use a= 11.7 x 10-6/°C and E=200 GPa. Answer:
Answer in two decimal places please
Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
A steel rod with cross-sectional area of 180 mm? is stretched between two fixed points. The tensile load at 25°C is 3,600 N. Assume a = 11.7x10-6 mm/ (mm-°C) and E = 200 GPa. a. Determine the temperature (in °C) at which the stress willI be zero? b. Determine the temperature (in °C) at which compressive stress will be at 48 MPa?
A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm
18