A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm

A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

d C
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The steel pipe shown has an outside diameter of 175 mm, a wall thickness of 18 mm, an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of ? = 11.7 x 10-6/°C. Using a = 335 mm, b = 870 mm, and ?= 60°, calculate the normal strains at Hand K after a load of P= 45 kN has been applied and the temperature of the pipe has been increased by 35°C O 16 mm, an e load of P= 45 kN has been applied and the temperature of the pipe has been increased by Answers: EH = Ek= H K με με
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
A rectangular steel bar with given dimensions is subjected to a axial compression. What is the critical buckling load? width, b = 42 mm thick, t = 60 mm L = 3.25 E = 180 Gpa
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places