In a steady flow through a nozzle, the flow velocity on the nozzle axis isgiven by v=uo(1+3x/L), where, x is the distance along the axis of the nozzlefrom its inlet plane and L is the length of the nozzle. The time required for afluid particle on the axis to travel from the inlet to the exit plane of the nozzleis(a)L40(b)340In 4(c)L4U0(d)L2.500

Answered: Image /qna-images/answer/8a3d33df-4bdc-4d45-a1d3-5247040da273.jpg

In a steady flow through a nozzle, the flow velocity on the nozzle axis given by v=uo(1+3x/L), where, x is the distance along the axis of the nozzl from its inlet plane and L is the length of the nozzle. The time required for fluid particle on the axis to travel from the inlet to the exit plane of the nozz is (a) Uo (b) L In 4 340 (c) L 400 (d) L 2.500

In a steady flow through a nozzle, the flow velocity on the nozzle axis given by v=uo(1+3x/L), where, x is the distance along the axis of the nozzl from its inlet plane and L is the length of the nozzle. The time required for fluid particle on the axis to travel from the inlet to the exit plane of the nozz is (a) Uo (b) L In 4 340 (c) L 400 (d) L 2.500

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An incompressible fluid is flowing at a steady rate in a horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameters di and d2 (where d₁ = 4d₂) that run for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-Weisbach friction factor to be the same. The velocity ratio between the bigger and the smaller branched pipes is
M27
Solve please
The Newtonian fluid shown in is confined between the plate and a fixed surface as shown in (Figure 1). Its velocity profile is defined by u = (8y-0.3y2) mm/s, where y is in mm. The plate has a surface area of 29(10³) mm² in contact with the fluid. Take μ = 0.482 N. s/m². Suppose that h = 6 mm. Figure h < 1 of 1 Part A Determine the force P that must be applied to the plate to cause this motion. Express your answer to three significant figures and include the appropriate units. xa P= 67.1 μA Xb a b X.10n < Return to Assignment mN Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining ? Provide Feedback
The flow of the fluid (laminar or turbulent) depends on: Viscosity, pipe diameter, and velocity True O False O
Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter (cm) Length (m) Friction factor 1 15 500 0,02 2 10 450 0.03 3 20 800 0,025 3. Determine the flow in pipe 3.
A centrifugal pump is used to pump a liquid in steady turbulent flow through a smooth pipe from one tank to another. Develop an expression for the system total head Δh in terms of the static heads on the discharge and suction sides zd and zs respectively, the gas pressures above the tanks on the discharge and suction sides pd and Ps respectively, the liquid density ρ, the liquid dynamic viscosity μ, the gravitational acceleration g, the total equivalent lengths on the discharge and suction sides (∑Le)d and (∑Le)srespectively, and the volumetric flow rate Q.
A cylindrical tank that is 2ft in dia. and 3ft tall is filled with a fluid with p=64lbmft3. find its density in slug/ft3, specific volume in in3/slug, specific weight in Ibf/ft3, total weight in pdl, and find the specific gravity of the substance compared to water.
In the figure shown, solve for the theoretical velocity of the jet, theactual velocity and the discharge through the orifice considering thefollowing:a) p1 = p2 = 0 Cc = 1.00 (rounded)h = 5 m of oil Cv = 0.97Do = 5 cmb) p1 = p2 = 0 Cc = 0.62 (sharp-edged)h = 5 m of water Cv = 0.98Do = 5 cmc) p1 = 70 kPa C = Cv = 0.95 (rounded)p2 = 0 Do = 7.5 cmh = 1.60 m (liquid with sp. gr. = 3)