2.) A liquid having a Reynolds number of 1500 flows thru a 200-mm diameter pipe, 220m long. The head loss of the pipe due to friction is 20m. Determine the following: d. Friction factor. e. Kinematic Viscosity of the Liquid. f. Rate of Flow.

2.) A liquid having a Reynolds number of 1500 flows thru a 200-mm diameter pipe, 220m long. The head loss of the pipe due to friction is 20m. Determine the following: d. Friction factor. e. Kinematic Viscosity of the Liquid. f. Rate of Flow.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid Mechanics. Reg.no : 5393 Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and that the water jet has a velocity of (Reg.No/100) m/s and a diameter of 60 mm. Find (a) the component of the force acting on the blade in the direction of the jet; (b) the force component normal to the jet; and (c) the magnitude and direction of the resultant force exerted on the blade. Note: Assume reasonable values for any missing data. Symbols have usual meaning unless otherwise stated.
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
Try to solving these problems: 1. Water at A has a pressure of 400 kPa and a velocity of 3 m/s. Determine the pressure and velocity at B and C. 150 mm 3 m/s 100 mm 50 mm B
An incompressible fluid is flowing at a steady rate in a horizontal pipe. From a section, the pipe divides into two horizontal parallel pipes of diameters di and d2 (where d₁ = 4d₂) that run for a distance of L each and then again join back to a pipe of the original size. For both the parallel pipes, assume the head loss due to friction only and the Darcy-Weisbach friction factor to be the same. The velocity ratio between the bigger and the smaller branched pipes is
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
Weter flows up a tapered pipe (figure). A differential mercury manometer is attached to the pipe at Wand B. The pipe has a diameter of 200 mm at A and 100 mm at B, the point B being 1 m above the alot A. Obtain the deflection in the manometer corresponding to a discharge of 50 L/s. Neglect the friction in the pipe. Relative density of mercury 13.6. %D 100 mm 1 m 200 mm
(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=1.7 ft/s h = H= 6.4 in. Air ↓ SG= 1.10 ft ft TH 3.8 in.
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
Oil (µ = 0.35 Pa-sec) flows through a horizontal 20 cm diameter circular pipe. The velocity at any point in the pipe’s cross-section a distance at a distance y from the center is: V =64(r² − y²) / μ where: r = 10 cm (radius of the pipe) Determine the following: a) Maximum flow velocity (m/sec) b) Shear stress (Pa) at the pipe’s centerline c) Shear stress (Pa) at the pipewalls?
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E-30,000 ksi, E10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assombly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.
9) Distilled water stands in glass tube of 9mm diameter at a height of 24mm. what is the true static height? use o=0.0742 n/m.