The 10-kg collar slides on the smooth vertical rod and has a velocity v₁ -2 m/s in position A where each spring is stretched 0.10 m. Calculate the velocity v2 of the collar as it passes point B. 0.40 m k = 800 N/m 10 kg B 0.40 m k = 800 N/m 2 m/s ww 95. T 0.30 m S. O2 uzatilmis Reference T₁ +V₁ (40) 2²+ 10.10.03+1 1800) (41) 2x2 2+me you var. 3.81 leaders. V= 2.26ms.✓ 20 + 30+ 80 = 201² + 10. 1/2 + T2 + V₂ = 'sach etkiyen yskyok 1 (10) √² + 10.10. (0) + 2 Mörzsek. 2(1.1(100)(012)

The 10-kg collar slides on the smooth vertical rod and has a velocity v₁ -2 m/s in position A where each spring is stretched 0.10 m. Calculate the velocity v2 of the collar as it passes point B. 0.40 m k = 800 N/m 10 kg B 0.40 m k = 800 N/m 2 m/s ww 95. T 0.30 m S. O2 uzatilmis Reference T₁ +V₁ (40) 2²+ 10.10.03+1 1800) (41) 2x2 2+me you var. 3.81 leaders. V= 2.26ms.✓ 20 + 30+ 80 = 201² + 10. 1/2 + T2 + V₂ = 'sach etkiyen yskyok 1 (10) √² + 10.10. (0) + 2 Mörzsek. 2(1.1(100)(012)

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
For the data given in this problem, determine the magnitude of the active thrust on the wall retaining a c soil, using the procedure discussed in Section 16.10. Given H = 15.0 ft, c = 100 lb/ft2, = 26, = 115 lb/ft3, kv = 0, and kh = 0.3.
A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = . Use Eq. (7.4).
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.