Task 5 A liquid of a density o flows through a pipe of a diameter d from a tank of a diameter D P. (with pressure PA) to another tank with significantly larger diameter (with pressure PB). Determine the mass flow rate m of the liquid flow and the pressure in the point C. Pe h OD D = 60 mm H = 1.2 m P = 110 kPa Given: d= 40 mm h = 0.3 m PA = 1.05 bar p= 1000 kg/m' n, Pc od Find: n = 5.73 kg/s pc = 108.4 kPa

Task 5 A liquid of a density o flows through a pipe of a diameter d from a tank of a diameter D P. (with pressure PA) to another tank with significantly larger diameter (with pressure PB). Determine the mass flow rate m of the liquid flow and the pressure in the point C. Pe h OD D = 60 mm H = 1.2 m P = 110 kPa Given: d= 40 mm h = 0.3 m PA = 1.05 bar p= 1000 kg/m' n, Pc od Find: n = 5.73 kg/s pc = 108.4 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FLUID POWER TECHNOLOGY 5) Figure 2 below shows the hydraulic system pumping oil (SG = 0.8) from a reservoir to a piston. The system consists of 13.72-m long 38-mm diameter cast iron pipe throughout, two 90º flange long radius elbows, a fully open globe valve and a sharp exit into the piston. K value is tabulated inside Table 1. If p1 = 7 bars, determine total head loss of the system and gauge pressure p2 in order to deliver water at 2 liter/s. Take kinematic viscosity of oil, = 1 × 10-4 m2/s.
2. A turbine is used to produce 2700 hp by expanding the water between points 1 and 2. Water flow rate, static pressures and pipe diameters are given. Calculate the power lost in between point one and two. Note that the static pressure at point 2 is given in vacuum. (SGH =13.6) P1 = 60 psi Q = 150 ft³/s D = 3 ft Section (1) Turbine 10 ft P2 10-in. Hg %3D vacuum D2 = 4 ft Section (2)
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0
Q1. The figure below shows a hot water tank, with a pumping arrangement to continuously circulate water in a loop. Plastic pipes used, with six bends and two gate valves, as shown. Given that the water is flowing at an average velocity of 2.5 m/s, calculate the required power input for the pump. Given: The density and viscosity of water at 60°C are p = 983.3 kg/m', u = 0.467x103 kg/m-s. Plastic pipes are smooth, and thus their roughness is very close to zero, ɛ = 0. The loss coefficient is K1 = 0.9 for a threaded 90° smooth bend and K1 = 0.2 for a fully open gate valve. Assume 70% pump efficiency. 1.2 cm Hot Water tank 40 m
Please solve and answer the question correctly please. Thank you!!
Water flows in a branched pipe as shown in Figure QS below. The water flows from Pipe A with a 165 mm diameter dividing into two smaller pipelines, Pipe D with a 97 mm diameter and Pipe B with an 81 mm diameter. The velocity in the 82 mm pipe (B) is 0.5 m/s and in the 97 mm pipe (D) is 0.43 m/s. Figure Q8 Calculate the velocity in m/s and the mass flow rate in kg/s in the 165 mm pipe (A) if the density of the water is 1000 kg/m³. Enter your answers to three significant figures. Velocity: m/s. Mass Flow Rate: kg s-1.
3b
b) A syringe is used to deliver vaccine against an infectious disease. This particular syringe is not perfect so it is expected that 5% of the vaccine flow rate out of the needle will leak past the plunger. If the vaccine has to be injected steadily with the flow rate of 270 cm³/min, and the plunger is moving at the velocity of 600 mm/min, sketch the control volume and determine the area of the plunger.
A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve
Ideal liquid flow Task 7 A liquid of a density p leaves a closed container through the piping system composed of a pipe of a diameter D and a pipe of a diameter d to atmosphere. Determine the mass flow rate m of the liquid flow and the pressure in the point A if the level of liquid in the container is equal to H and a gauge pressure of the gas in the container is equal Apo. Assume that the container has significantly larger cross-section area than the pipe cross- A sections. h D = 30 mm H = 0.8 m Pa = 1.0 bar Given: d = 20 mm h = 0.5 m p= 1000 kg/m³ Ap. = 15 kPa m, Pa Pa Find: ṁ = 2.34 kg/s; pa = 117.4 kPa
answer in complete solution