A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve

A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given, Point A - Inlet of a water pipe Pressure at the inlet of a water tap = 300kPa Water Pipe internal dimension is = 30mm Water Temp = 20 degrees Point B - section of pipe Pressure = unknown Open to atmosphere. elevation drop of 20m from point A to Point B Assume frictionless piping system. Assume turbulent flow. What is the pressure and flow rate at point B?
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.225 kPa b.100 kPa c.75 kPA d.150 kPa PLEASE INCLUDE FIGURE OR FBD
Please fast only final answer needed
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H=51+25.98(Q^2) B) H=54+24.98(Q^2) ⒸH=54+25.98(Q^2) ⠀
Problem 2 - Pumps in Parallel Two 32-in pumps, with performance curve shown below, are combined in parallel to deliver water at 60°F through 1500 ft of horizontal pipe. If f = 0.025, what pipe diameter will ensure a flow rate of 35,000 gal/min for n = 1170 rev/min? 1170 r/min 800 50 NPSH 700 600 500 400 300 200 Total head, ft 0 36-in dia. 32-in dia. 28-in dia. 4 8 82% 85% 1500 bhp 87% 88% 3000 bhp, 3500 bhp 87% 2500 bhp 2000 bhp 12 16 20 24 U.S. gallons per minute x 1000 28 8 8 8 8 NPSH, ft 40 30 20
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
Please don't provide handwritten solution ....
For the duct system, plot required fan head Hrequired (mm of water column) as a function of volume flow rate V. (Lpm). On the same plot, compare available fan head Havailable versus V. , and mark the operating point. Discuss.
In the hydroelectric power plant whose cross-section is given, the flow rate of Q=33.045 m^3/sec is transmitted to the power plant through a D=1.6 meter diameter penstock. Ignoring friction losses; a) Find the internal pipe pressure at point 2 ( at the below ). b) Find the resultant force (F) and its direction (O) that the water exerts on the fixation mass. c) Calculate the electrical power generated in the plant. (Pwater= 1 ton/m^3, Ywater= 9.81 kN/m^3, g=9.81m/s^2, Beta= 45 degree
Find the flow rate through the siphon and the pressure at the siphon apex. E.L. 130 m 물 -E.L. 120 m 1=1,500 m d=20 cm f=0.018 FE.L. 100 m Consider reasonable K s c, K s e, Kb values. 1=1,500 m
show dolution and diagrams.
Q.2 A centrifugal pump is required to pump water to an open water tank situated 4 km away from the location of the pump through a pipe f diameter 0.2 m having Darcy's frřiction factor of 0.01. The average speed of waterinthe pipe is 2 m/s. If it is to maintain a constant heac of 5 m in the tank, neglecting other minor losses, the absolute discharge pressure at the pump exit is (a) 0.449 bar (c) 44.911 bar dund (b) 5.503 bar (d) 55.203 bar