Q11 Calculate the power required for a water pump used in a closed system with a flowrate Q=0.0076 m³/s. Assume that the section area=0.00511m2 and the discharge(7 marks)area=0.0037m².WaterSuctionDischargepumpOutlet gauge pressure=250 kPaInlet gauge pressure=147 kPa

Detailed explanation:Given ValuesInlet gauge pressure=147 kPaOutlet gauge pressure=250 kPaFlow…

Answered: Q11 Calculate the power required for a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the recommended minimum speed (rpm) for a radial flow pump operating at 0.143 m³/s of water against a head of 291 m.
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve
Part A plz
QUESTION 3 A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency. A 27 kba 12 m
A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve
Exercise Problem No. 1: An agricultural land install a pump with a 218mm diameter suction pipe and a 200mm diameter discharge pipe. Respectively each pressure reads 1.12 bars and 0.96 bars. The water flow measured 12,500 liters/min.at normal temperature. Calculate the following: 1.Head at the discharge side, m 2. Velocity Head, m 3. Total Head of the pump, m
### Develop a conclusion of a piping design report for the choice of a pump, based on the calculated parameters of flow Q = 10 l/s, power of 10kw taking into account that the head of 60 mca adopted was higher than that calculated for safety, and that the pump was chosen through the WebCAPS catalogue of the company GRUNDFOS. The pump chosen was the GRUNDFOS CR 32-3 A-F-A-E-HQQE
For the hydraulic system of Figure 8, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3(b) The pipe inside diameter is 0.0254m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Q11 Calculate the power required for a water pump used in a closed system with a flow rate Q=0.0076 m³/s. Assume that the section area=0.00511m2 and the discharge (7 marks) area=0.0037m². Water Suction Discharge pump Outlet gauge pressure=250 kPa Inlet gauge pressure=147 kPa