A pump is tested in the laboratory and the following data were obtained. Determine the pump efficiency. Torque = Rotational speed Inlet pressure = Outlet pressure = Volume flow rate = Height to inlet gage = Height to outlet gage = Inlet flow line = Outlet flow line = Fluid T = 47.5 J @ P1 P2 Q Z1 Z2 = 3600 rpm = 17.25 kPa octane = 206.8 kPa = 0.063 m³/s = 0.61 m = 1.52 m 10-nominal schedule 40 8-nominal schedule 40

A pump is tested in the laboratory and the following data were obtained. Determine the pump efficiency. Torque = Rotational speed Inlet pressure = Outlet pressure = Volume flow rate = Height to inlet gage = Height to outlet gage = Inlet flow line = Outlet flow line = Fluid T = 47.5 J @ P1 P2 Q Z1 Z2 = 3600 rpm = 17.25 kPa octane = 206.8 kPa = 0.063 m³/s = 0.61 m = 1.52 m 10-nominal schedule 40 8-nominal schedule 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
4. A pump is tested in the laboratory and the following data were obtained. Torque = T= 6.78 Nm Rotational speed = w = 20 Hz Inlet pressure = P1 = 68.95 kPa Outlet pressure = p2 = 193 kPa Velocity in the inlet line = V= 2.44 m/s Height to inlet gauge = z1 = 0.61 m Height to outlet gauge = 22 = 1.52 m Inlet flow line = 2- nominal schedule 40 Outlet flow line = 2- nominal schedule 40 Fluid = Water a) Determine the pump efficiency. b) Consult an actual pump catalog and select a pump for these conditions.
Q4/A- The mass of the filter is 25.3046 gm. after 20 min the filter mass will be 25.4112 gm. with volumetric flow is 5.2 m 3/hr. What is the concentration of pollutant after one day
A 2:1 scale model of a pump was tested in a laboratory at 750rpm, head 20m and discharge 10 1/s. If the speed of prototype was 1500rpm, determine the head. (hint : use equation of flow coefficient)
a) Develop an equation for the head (in ft) developed by the pump described by the chartas a function of flow rate (in gpm) when the pump uses a 9 ¾” impeller. b) Develop an equation for the pump efficiency as a function of flow rate (gpm) when the pump uses a 9 ¾” impeller.
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
Shown below is a performance data for a water pump. For each row of data, calculate the pump efficiency (percent). Estimate the best efficiency point (%) and the volume flow rate (gpm) and net head (ft) at the best efficiency point. gpm ft KW 200 75 4.9 300 73 6.7 400 71 7.2 500 66 8.1 600 60 9.0
Don't give wrong answer please
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
ES Font English (United Kingdom) ▬▬ Q Search > Text Predictions: On ALT Paragraph S Accessibility: Good to go Styles The following parameters characterise a liquid-fuelled rocket engine: stagnation pressure P0=100bar; stagnation temperature TO=3300K; nozzle exit diameter DE=1.0m; throat diameter=0.1 m; gas constant R=692 Jkg-1 K -1; ratio of specific heats cp/cV=y=1.25. Estimate the following: static pressure at the exit plane, exit Mach number. Heading Focus Editing ENG UK
Toplam basınç göstergesi Manometre Vana Venturimetre Debiölçer Hazne Pompa Manometre=Manometer Venturimetre=Venturimeter Debiölser-Flaw meter Vana=Valve Pompa=Pump Hazne=Tank Toplam Basınç Göstergesi =Total Pressure Gauge It is desired to display the flow in the venturimeter, How can you determine this? Explain bY. explaining the method vou bave chosen.
%3D Find the pressure in KN/m2 at the center of pipe A. T = 10°C. Oil (S = 0.85) Water 90 cm 150 cm Water 30 cm Mercury (S = 13.6) to 30 cm