Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H-51+25.98(Q^2) B) H=54+24.98(Q^2) H=54+25.98(Q^2) ⠀

Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft^3/s. Hint: You need to use the Tioga table and K value for minor losses. Z₂ = 107 ft Reservoir B 90° regular screwed elbow Pump Z₁ = 53 ft Reservoir A A) H-51+25.98(Q^2) B) H=54+24.98(Q^2) H=54+25.98(Q^2) ⠀

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is Total Head of submersible pump has Q=287 l/sec D=0.8 m Lenght of pipe=12000 m Fluid=water Fittings=6 elbows 45 degree Material=GRP Depth of well=9 meter Please take your time
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 3.At section 1 of a pipe system carrying water the velocity is 3.0 fps and the diameter is 2.0 ft. At section 2 thediameter is 3.0 ft. Find the discharge and velocity at section 2.
3. . In a differential pressure flow meter, determine the velocity at the outlet for the given technical specification. The density of the liquid flowing through the pipeline is 997 kg/m³, Pressure at inlet is 10 Ib/ft2, pressure at outlet is 8 Ib/ft2 and cross sectional area of the orifice is 0.2512 m. Note: Ratio of meter diameter to pipe diameter is 0.5 and discharge coefficient is 0.61. Also, find the differential pressure and flow rate.
Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe in the one inch branch is 8 ft. Brine (sg=1.04, m=10-3Pa*s) flows at 250gpm through the entrance at point A. Assume fully turbulent flow in both branches (f=ft). Pipes are standard Schedule 40 steel pipes. Assume the globe valve is partially shut so its equivalent L/D is 1000. For Part 1 of this project, you are tasked with determining the following: The flow rate in both branches The pressure drop in both branches The overall resistance coefficient
State clearly your assumptions in your solution sheet
4
I need the answer at 20 minute
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
5
1. Specify the sizes of pipes (cast iron, schedule 40 ) and the size of the motor to be used for a pump to lift water at 50 from reservoir A to reservoir B. Consider the following data: Total static head Fittings and valves: Suction line Discharge line Length of straight pipe: Suction pipe Discharge pipe Absolute viscosity of water Absolute roughness of cast iron Water velocity 50 m 1 foot valve, 1 standard elbow 1 gate valve 1 check valve (same as close return valve), 1 gate valve, 1 long sweep elbow, 2 standard elbow 300 m 80 m 0.001002 Pa-s 0.00026 m m 1.18 -2.75 S Pump efficiency 80% Note: Neglect the head loss in the foot valve and at the pipe exit in the discharge reservoir and do not equal sizes for the suction and discharge pipes. Draw the piping system.
Calculate the Flow Rate of water at 5°C through the system below. Q = Flow 3.4 m 700 kPa 30 mm diameter DN 65 mm Schedule 40 Pipe
show dolution and diagrams.