Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown in figure below. The pipe properties are given in table below. The water surface levels of the reservoirs A and B are 100m and 80m, respectively. Neglect the minor losses. Determine the flow rate in each pipe of the system. Take f-0.02.

Q2/ Four pipes A, B, C, and D form a system of pipes that connects two reservoirs A and B, as shown in figure below. The pipe properties are given in table below. The water surface levels of the reservoirs A and B are 100m and 80m, respectively. Neglect the minor losses. Determine the flow rate in each pipe of the system. Take f-0.02.

Name: Q2/ Four pipes A, B, C, and D form a system of pipes that connects tw
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2/ Four pipes A, B, C, and D form a system of pipes that connects tworeservoirs A and B, as shown in figure below. The pipe propertiesare given in table below. The water surface levels of the reservoirsA and B are 100m and 80m, respectively. Neglec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Please give detailed explanations and show your work clearly - I will be using this to study for an…

A: The Navier–Stokes equations contains a set of differential equations which describes the motion of…

Q: 2. Oil with a S.G. pf 0.82 is flowing in a pipe under the condition below (see figure). If the total…

A: Given data as per the question The specific gravity of oil =0.82 Total head loss =3 ft Q =2.08 cfs…

Q: Based on the layout of the water supply system, how much pressure in psi will be available at the…

A: Given:Pressure at the source, P1=75 psi=75*144 lb/ft2=10800 lb/ft2Water flow rate, Q=3.75 cfsPipe…

Q: A constriction in a pipe will cause velocity to increase and pressure to fall at the throat. The…

Q: Water flows through the pipe contraction shown in the figure below. For the given d=0.11 m…

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…

Q: Qu: Water is flowing in pipeline shown in the figure; calculate the required dianeter (d), for the…

A: find the diameter ''d''.

Q: 4. A tank is full of water and open at the top as shown in the figure. There is a frictionless…

Q: Water flows from a lake as is shown in the Figure at a rate of 4 cfs. Is the device inside the…

A: Given:Water flow rate, Q=4 cfsFriction factor, f=0.015Elevation of water in the lake, z1=356…

Q: 2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in…

Q: The pump in the figure shown draws water from a reservõir and discharge through a which terminates…

Q: A reservoir has a depth of 20 ft. A pipe at the base of the reservoir needs to convey discharge of 2…

A: Given data: A reservoir has depth h=20 ft Discharge…

Topic Video

Question

Q2/ Four pipes A, B, C, and D form a system of pipes that connects two
reservoirs A and B, as shown in figure below. The pipe properties
are given in table below. The water surface levels of the reservoirs
A and B are 100m and 80m, respectively. Neglect the minor losses.
Determine the flow rate in each pipe of the system. Take f=0.02.
Pipe
Diameter (m)
Length (m)
A
0.3
500
B
0.15
1000
0.15
1000
D.
0.3
750
Z-100 m
Please solve a question
according to the data of the
request
Reservoir A
Pipe A
Pipe B
Note: Figure not to
scale
Pipe C
Z-80 m
Reservoir B
Pipe D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Step 1

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You are evaluating a pipe network transporting water from a large river reservoir to the citywater storage facility. According to the pipe specifications, the pressure leaving the pipe network(continuing to city storage) cannot exceed 3 psi. Given Qa, pipe diameters (Da – Dd), determinethe pressure exiting the pipe network. Do the city designers need to reconfigure the set-up. Usethe Hazen-Williams equation to determine the head losses. All pipe lengths are 200 feet long,and the pipes are made of recently installed galvanized iron. given below Flow rate and Diameter for all 4 pipes: Q_a=42 csf, D_a=4ft, D_b=3.2ft, D_c=7ft, D_d=2.1ft.
Question 3 Consider 2 which shows a pipe system connecting two reservoirs. The pipe diameter changes at point B as shown in the image A 10 cm 23 m NOT TO SCALE Figure 2: 9 m 6 cm с 3 m 1. Describe what is referred to by the hydraulic gradient line and the energy gradient line. What is the difference between the two levels? In what scenario will the energy and hydraulic grade lines coincide? 2. Calculate the velocities in the two segments of the pipe. Take into account the friction losses through the pipe, entry loss to the pipe and the shock contraction losses at B. Take the pipe friction factor as 0.005 and the coefficient of contraction at B as 0.6. 3. Draw the energy gradient line and the hydraulic gradient line for the system.
fluid mechanics
The water is flowing through a pipe having diameters 30 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 40 litres/s. The section 1 is 7 m above datum and section 2 is 3 m above datum. If the pressure at section 1 is 37 N/cm? , find the following by neglecting losses: (ENTER ONLY THE VALUES BY REFERRING THE UNIT GIVEN IN BRACKETS) ) Area of cross section of section1 (unit in m?) = Area of cross section of section2 (unit in m?) = velocity at section 1 (unit in m/s) = velocity at section 2 (unit in m/s) = (ii) difference in datum head (Unit in m) = Pressure head at section 1 (Unit in m) = pressure head at section 2 (unit in m) =
= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
Help !! Don't copy from othersites ,write the variables clearly. Solve using the energy equation.
Hydraulics
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and is into the reservoir) Assume ha = 10 m, hg = 50 m, hc = 0 m, l₁ = 300 m, l₂ = 250 m, and 3 = 500 m. QA = QB Qc= i Elevation = h VA D₂=0.08 m = = 0.020 Elevation = h у в D,= 0.10 m f = 0.015 < D₂ = 0.08 m f = 0.020 Elevation = h с
C2. A circular pipe 1 of 535 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters 325 mm and 180 mm respectively as shown in figure below. If the average velocity of pipe 1 and pipe 3 are 4.7 m/s and 3.85 m/s and the flow rate of pipe 2 is 1/3rd water flow in pipe 1. D2 Pipe 2 Pipe -D, Find the following: (3 Marks) O Flow rate of water through pipe 1 in m/s (m Velocity (V)) of pipe 2 in m/s (iin) Flow rate of water (Q3) through pipe 3 in m/s
I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The then breaks into N narrow Pipes (which have a diameter, d2, and a length, L2), before the water is released to the atmosphere, as shown in the figure. The entrance to the small pipe from the large pipe has a loss coefficient of KL. You may assume the flow is laminar and fully developed everywhere in the system, and that any changes in height are neglible. (The viscosity is NOT negligible) a) Find an expressin for the velocity of water leaving the sprinkler b) Find an Expression for the gauge pressure at point A, a distance L1 upstream of the narrow pipes. Express your answer in terms of the flowrate, Q. c) The inner diameter of the first segment of the pipe is d1 = 10mm, the inner diameter of the second set of pipes is d2 = 1mm, with N = 25. The flowrate through the sprinkler is Q = 0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds…
help
I am having trouble with this problem.