Problem 1:Consider the pipe system presented here. You have fluid flowing into a pipe atPoint A. Point B is capped, so no fluid is flowing out of the top of the pipe. Thereare two outlets: Point C and Point D. If water flows in the Pipe at Point A with aVelocity at 8 m/s and has a diameter of 100 mm. The outflow pipes at Point C andPoint D each have a diameter of 20 mm. The height of the pipe is 5 meters.Determine the Velocity at Point D and Point C. What is the pressure of the fluid inthe Pipe at Point A?Point DPoint BPoint CTPoint A

Step 1: THE VELOCITY AT THE POINT C AND D. Step 2: THE PRESSURE AT THE POINT A

Answered: Problem 1: Consider the pipe system…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If a pipe with flowing water has a cross-sectional area nine times greater at point 2 than at point 1, what would be the velocity at point 2 if the velocity at point 1 (2 m/s)?
Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the line are 6-in-diameter cast iron pipes, while the middle 200 ft consists of two 4.24-in-diameter cast iron pipes. Find: a. Provide a diagram b. the average velocity in each section of pipe, c. the pressure drop in each length of pipe, and d. the total pressure drop.
Heavy machine tool lubricating oil (ref. Appendix C applied fluid mechanics) is pumped through six rectangular slots in a heat exchanger (oil flows in the white rectangles in section view a-a) as shown below. You may assume that the oil flows through the heat exchanger with a constant temperature of 40°C. If the flow rate from A to B is 3 cm³/sec determine the Reynolds number for the oil flow. Is the flow laminar or turbulent?
Parvinbhai
Problem 5- Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the difference in elevation is 50ft? (v= .001 ft²/s)
A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing process, both pastes are pumped through a pipe, with the red paste lying in the center of the pipe, as shown in Figure Q2. The pipe has an internal radius, R2, and the segment of red paste has a radius R1. The flow is found to follow the Poiseuille equation, i.e. 1 dp u(r) = -- 4µdx (R²2-²) Where u is the viscosity of the paste and dp dx is the pressure gradient. The total flow of toothpaste through the pipe is Qtot, and the flowrate of the red paste is Qred. The toothpaste has a density of p = 1200 kg/m3, and a viscosity of 0.03 Pa.s. The pipe has a radius R2 = 5 cm and a length L = 2 m. a) Find an expression for the flowrate of the red toothpaste. You answer should be in terms of µ, R1, R2, dp dx) b) The flow in the pipe becomes turbulent when the Reynolds number reaches 2000 (where Re is calculated using the mean velocity across the pipe). What is the maximum pressure drop along the pipe…
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS