For the flow configuration shown, you are required to design a pump station to transfer water from the bottom tank to the upper tank. In your own words, explain the steps that are needed to be followed for the design of the pump system. Your answer should be typed and not more than one page. The pipe equivalent roughness is 1.5 mm. And a valve with a k=10 is located just upstream of the lower reservoir (other losses are negligible). Take p=1000 kg/m”, g = 9.81 m/s?, and u = 1.179 x 102 kg/m.s.

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: It is desired to pass water from point 1 to point 3 by means of a hydraulic pump, both tanks are…

A: Given: the external diameter of pipe, D = 28 mm The thickness of pipe, t = 2 mm The friction losses…

Q: A piping system is to be installed at place where the pump will transfer the fluid from tank A to…

A:

Q: Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to…

A:

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure). The…

A: Given that, Flow rate of water, q=95 gal/minq=0.0066 m3/sec=0.2339 ft3/sec,Inner diameter of pipe,…

Q: The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger…

A: Larger end: D1= 0.50 cmZ1= 7 mV1= 1.2 m/sP1= 5200 kN/m2 Smaller end: D2= 0.20 cmZ2= 3 m   To find:…

Q: A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a hole in…

A: Consider the water level in the tank at instant t as h as shown. That means it takes time Here H is…

Q: A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

A:

Q: ● Compute the time needed for the cylinder position to retract from the maximum position 1m to…

A:

Q: What is the power ratio of a pump to its 1/5 scale model if the ratio of the heads is 4 to 1?

A:

Q: 6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge…

A:

Q: A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The…

A:

Q: To compute the friction factors, you are assuming that the only losses in the system are due to…

A: Whenever fluid flow through the pipes there is always some kind of head loss is happened due to the…

Q: 0 oil volume flow rate

A: given:

Q: In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft…

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required  pump power.

Q: For the wye fitting below, which lies in a horizontal plane, the cross-sectional areas at sections…

A: Given Data The area of the section 1 is: A1=1 ft2 The area of the section 2 is: A2=1 ft2 The area…

Q: Consider the pump on the right side of the drawing, which acts to reduce the air pressure in the…

A: The pressure exerted by a fluid at equilibrium due to gravity at any point in time is known as…

Q: Question 2 A valve is used to regulate flow in a water pipeline. The pipe has a diameter of 400 mm…

A: Given: Diameter of the pipe→D=400 mm=0.4 m Length of the pipe→L=2500 m (1) Effect of the water…

Q: 1. Specify the sizes of pipes (cast iron, schedule 40) and the size of the motor to be used for a…

A: Given Data: Flow rate, Q = 50 litres/s = 0.050 m3/s Total static head = 50 m Velocity of fluid in…

Q: A six-centrifugal pumps delivers 0.1 m3 /s against a total head of 480 m. What is its specific speed…

A: Given: The value of discharge is, Q=0.1 m3. The value of the head is, H=480 m. The value of speed…

Q: Example (2-2): Find the specific speed of a double suction centrifugal pump delivering 1.5 m/s…

A: Data given-  Q = 1.5 m3/s  H = 15 m  N = 725 rpm

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…

A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…

Q: 2. The diameter of a pipe at the larger end is 0.5 cm and at the smaller end is 0.2 cm, the larger…

A: Data given - PA = 5200 kN/m2  VA = 1.2 m/s  DA = 0.5 cm  DB = 0.2 cm  ZA = 7 m  ZB = 3 m

Q: Apply the formulas in designing a hydraulic turbine to select the appropriate type of turbine for…

A:

Q: Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of…

A:

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A:

Q: Determine the least number of stages for a multi-stage pump to deliver 80 L/s against a total head…

A:

Q: Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc.,…

A:

Q: A chamber has a leak size of 10-3 SCCS. Assume this is the only gas load on the system. The chamber…

A: A pump is a mechanical device that transports liquids (liquids or gases). Pumps are divided into…

Q: The figure below shows a duct into which water flows. The left end of this pipe represents a section…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.