(b)Sketch clearly all the electrical appliances in Table Q1(a) into floor plan schematicdepicted in Figure Q1(b) according to the standard symbol renowned by EnergyCommission (EC). Table Q1(a)LocationLoadNos.DemandEstimated Power(W)FactorChandelier lamp12000.1Fluorescent lampSSO (13A )Air-conditioner (1HP)Wall lampSSO (13A )Wall lamp360.8Living Hall2500.517500.51360.6Bedroom 12500.5360.6Bedroom 2 Ceiling fan1000.8SSO (13A )Wall lamp2500.51360.6Bedroom 3Wall fan1600.8SSO (13A )Fluorescent lampSSO (13A )Fluorescent lampExhaust fan2500.5360.8Hall12500.5360.8Kitchen360.5SSO (13A )Globe lamp2500.51360.6ToiletWater Heater13k0.3Bedroom 1Bedroom 2Living HallToiletHallKitchenBedroom 3Figure Q1(b)

Apart from the common electrical symbols for resistor, capacitor, and inductor. The electrical…

Table QI(a) Location Load Nos. Estimated Power Demand (W) 200 Factor Chandelier lamp Fluorescent lamp SSO (13A ) Air-conditioner (IHP) Wall lamp SSO (13A ) Wall lamp Bedroom 2 Ceiling fan SSO (13A ) Wall lamp 1 0.1 2 36 0.8 Living Hall 250 0.5 0.5 0.6 750 36 Bedroom 1 250 0.5 36 0.6 100 0.8 250 0.5 1 36 0.6 Bedroom 3 Wall fan SSO (13A ) Fluorescent lamp SSO (13A ) Fluorescent lamp Exhaust fan SSO (13A ) | Globe lamp 60 0.8 250 0.5 36 0.8 Hall 250 0.5 36 0.8 Kitchen 36 0.5 2 250 0.5 36 0.6 0.3 Toilet Water Heater 1 3k Bedroom 1 Bedroom 2 Living Hall Toilet Hall Kitchen Bedroom 3

Table QI(a) Location Load Nos. Estimated Power Demand (W) 200 Factor Chandelier lamp Fluorescent lamp SSO (13A ) Air-conditioner (IHP) Wall lamp SSO (13A ) Wall lamp Bedroom 2 Ceiling fan SSO (13A ) Wall lamp 1 0.1 2 36 0.8 Living Hall 250 0.5 0.5 0.6 750 36 Bedroom 1 250 0.5 36 0.6 100 0.8 250 0.5 1 36 0.6 Bedroom 3 Wall fan SSO (13A ) Fluorescent lamp SSO (13A ) Fluorescent lamp Exhaust fan SSO (13A ) | Globe lamp 60 0.8 250 0.5 36 0.8 Hall 250 0.5 36 0.8 Kitchen 36 0.5 2 250 0.5 36 0.6 0.3 Toilet Water Heater 1 3k Bedroom 1 Bedroom 2 Living Hall Toilet Hall Kitchen Bedroom 3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For each of the following power systems, do following: 1. Compute the Y_bus in rectangular and polar forms 2. Set up the power flow problem as follows (see the sample example) Identify the type of each bus State the unknown and known variables at each bus Write the power flow equations
5
ANSWER THE FOLLOWING PROBLEM: MAKE SURE TO SHOW YOUR COMPLETE SOLUTION AND ANSWER MUST BE IN FOUR DECIMAL PLACES. 1. The load taken from a supply consists of (a) lamp load 10 kW a unity power factor (b) motor load of 80 kVA at 0.8 power factor (lag) and (c) motor load of 40 kVA at 0.7 power factor leading. Calculate the total load taken from the supply in kW and in kVA and the power factor of the combined load.
Hydro 3.10% DIST, 0.1% HYD, 14.8% Solar Others 0.60% 0.10% Gas COAL, 26.3% GAS, 58.8% 42.30% Coal 53.90% TNB Generation Fuel Mix FY 2009 TNB Generation Fuel Mix FY 2019 Figure 1 TNB Generation Fuel Mix for 2009 and 2019
Please do all three parts And diagram Asap
2) This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course. just write for me the the correct answer.
Justify only three of the following: (a) low efficiency of the steam power plants, (b) low efficiency of the gas power plants, (c) high running cost of deasil plants (d) using the surge tank in hydroelectric plants
(i) Figure Q1 shown below presents a one-line diagran simple power system with two generators. Tabl¢ gives the corresponding line parameters. Form admittance matrix for the given system. Table Q1. Power line parameters Figure Q1. Power system
Please answer all subpart either dislike Please all subpart is compulsory
How can i complete this ?
A. X B What logic gate has the same function as the circuit above?
14. For a power plant with two units, the weekly load is 1200 MW. The coal consumption (tons/hour) for each unit is Q₁ 16+.3P₁ tons/hours Q2-25+.4P₂ tons/h The total coal available to the plant is limited to 90,000 tons/week. If the linear cost curves are given as C₁=495+11P₁ $/hour, C₂-760+10P₂ $/hour And generation by each unit is limited to 150 ≤ P, ≤ 600MW Determine the values of P₁ and P₂ for minimizing the cost of power generation. 15. Use LP to determine economic dispatch if C₁ = 5+ 3P₁, C₂ = 7+6P2, C3 = 8 + 9P3 50 P₁ < 150 MW and PD=210 MW If the line flow P12= .3P₁ + .4P₂ + .1P3, also determine P₁, P₂ and P3 so that P₁2 is limited to 70 MW. 1 4 400 ≤ P₂ ≤1000MW H 2 3