Stery readings, calculate the complex impedance of the mystery component. Where X and Y are the last 2 digits of your student number. For example: If your number is C1700123, then the current = 250+23 = 273 A If your number is C1700100, then the current = 250+00 = 250 A Current Carrying Conductor Mystery Component Power Meter Readings Current=250+XY A P=5 kW Q-7 kVAr Frequency = 50.2 Hz Figure 2

Stery readings, calculate the complex impedance of the mystery component. Where X and Y are the last 2 digits of your student number. For example: If your number is C1700123, then the current = 250+23 = 273 A If your number is C1700100, then the current = 250+00 = 250 A Current Carrying Conductor Mystery Component Power Meter Readings Current=250+XY A P=5 kW Q-7 kVAr Frequency = 50.2 Hz Figure 2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.36P

See similar textbooks

Similar questions

Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
High voltage engineering subject
A generator operating at 50 Hz delivers 1 pu power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place. reducing the maximum power transferable to 0.5 pu whereas before the fault, this power was 2.0 pu and after the clearance of the fault, it is 1.5 pu. By the use of equal area criterion, determine the critical clearing angle.
Lighting arresters are used in power system to protect electrical equipment against a. Direct stokes of lightning b. Over-voltages due to indirect lightning stroke c. Power frequency over-voltages d. Over-currents due to lightning
Voltage sags due to short circuit and earth faults are the cause for the vast majority of equipment problems. Electronics equipment become more susceptible to voltage sag, hence the companies experience production stoppages. Voltage sag analysis is very complex issue. Based on voltage sag randon factors describe on it.
A generator operating at 50Hz delivers 1 pu power to an infinite bus through a transmission circuit inwhich resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 puwhereas before the fault, this power was 2.0pu and after the clearance of the fault, it is 1.5 pu. By theuse of equal area criterion, determine the critical clearing angle.
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
As per bartleby honor code I can submit 3 questions So please answer all
X=2 Y=8
Subject name: Power System Protection
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1450 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the rated current will the inrush current be when the ASM is started directly?