QUESTION SEVEN A single-phase ac voltage controller has a purely resistive load. The given data are V₂ = 250 V. f = 50 Hz, and R = 4.5 2. Determine the (a) value of a that gives an rms output voltage of 125 V. (b) maximum rms value of the current obtainable over the permissible range of a, (c) maximum average value of the thyristor current obtainable over the permissible range of a, (d) amplitude of the seventh harmonic current when a = x/6, (e) input power factor with a = x/6, (f) angle for which the forward blocking voltage occurs for the thyristors, and (g) angle for which the reverse blocking voltage occurs for the thyristors.

QUESTION SEVEN A single-phase ac voltage controller has a purely resistive load. The given data are V₂ = 250 V. f = 50 Hz, and R = 4.5 2. Determine the (a) value of a that gives an rms output voltage of 125 V. (b) maximum rms value of the current obtainable over the permissible range of a, (c) maximum average value of the thyristor current obtainable over the permissible range of a, (d) amplitude of the seventh harmonic current when a = x/6, (e) input power factor with a = x/6, (f) angle for which the forward blocking voltage occurs for the thyristors, and (g) angle for which the reverse blocking voltage occurs for the thyristors.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject: Electrical Circuit (EE2) ***Need asap pls. Thank you.
a. Description of lamp-ballast system b. Choose the power rating of T8 fluorescent lamp to be used in the system c. The operation of lamp-ballast circuit d. The modelling of the lamp-ballast by an equivalent circuit e. The design of inductance of the choke of the lamp-ballast system f. Determine the supply current and power factor g. Decide the desire power factor to be achieved and state the reason for the chosen of that value of power factor h. The design of size of capacitor for power factor correction. i. Team members information
14 The ac bridge of Figure 48 nulls with R₁ = 1 kN, R₂ = 2 kn, R3 = 100 2, and L3 = 250 mH. a. Find the values of R, and L₁. b. If the circuit is excited by a 5-V rms, 1-kHz oscillator, find the offset voltage for L₁ = 510 mH. c. What are the amplitudes of the in-phase and quadrature (90°) components of the offset voltage? FIGURE 48 ac bridge for Problem 14. Ro D
What is the answer for Question 10
Exercise 1: Verification of Ohm’s law for a simple circuit across a Sinusoidal AC Supply Calculate the following: i. Current flowing through the resistor. (Irms) ii. Calculate the peak to peak voltage (Vpk-pk) and peak-peak current (I pk-pk) iii. Calculate the time period of the waveform
Materials in parallel, supplying a load of 500 amps, with a terminal voltage of 240 volts, and the resistance of the product circuit 0.04 Ohm The resistance of the field circuit is 60 ohms. Calculate a. Product current b. field current c. electromotive force
a. A circuit with half-wave rectified signal has a dc voltage of 0.318Vm. The rms value of the ac component of the output signal is 0.385Vm. Calculate the percentage ripple of a half-wave rectified signal.
Number 5 Please show your detailed solution.
4) A single-phase full-wave AC voltage controller consists of two SCRs connected in invers-parallel. The supply voltage is 220V at 50Hz. The controller is used to control heater element of 2500W in an electric oven. The trigger angle is 30o. i) Draw the circuit diagram ii) sketch compatible waveforms for the supply, load and SCR voltages. iii) calculate the rms value of the load voltage and current. iv) Determine the input power factor of the circuit. v) Calculate the average value of the SCR current.
(b) A single-phase half-wave AC voltage controller has a resistive load of R = 7 N and the input voltage V=165 V (RMS), 50 Hz. The desired output power is P. = 1867 W. (i) Calculate the delay angle a. (ii) Determine the input PF (iii) Calculate the output DC voltage.
Q3) A 3-phase half-wave controlled supplies a resistive load of 100 Q from a 380V, 50 Hz supply. Calculate the average load voltage, the average load power, the operating power factor and the voltage ripple factor for trigger angles of 45° and 90°.