Answered: A The value of: A=5 ms C= 15 ms Peak to…

A The value of: A=5 ms C= 15 ms Peak to peak = 10 B D Figure 1 (a) From Figure 1 above, identify the frequency (f), value of time at A, B, C, D, period (T) and the RMS.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

b) Determine the voltage ?(?) and current ?(?) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors ?L, ?r and ?c. e) Sketch the phasor diagram showing ?s, ?r, ?r, ?c and ?.
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequency of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms - (iii) Determine phase relationship between voltage and current waveform. (c) From the measurement process, the circuit generated two different outputs, V,(t) and V,(t) with the same peak voltage. The V,(t) lagging V,(t) by 100°. If V,(t) =150sin(1000t – 40°)V , determine the RMS value and phase angle of.
(b) An engineer is required to analyse a sinusoidal waveform for the voltage and current using oscilloscope. The voltage waveform produced Root Mean Square (RMS) value at 75 V with positive-going zero crossing at 30°. While the RMS value of current is 66.71 A with negative-going zero crossing at 0.349 rad. Assume the frequeney of both waveforms is 50 Hz. (i) Sketch the voltage and current waveform in the same axis by showing the important point. (ii) Determine instantaneous voltage when t = 8ms . (iii) Determine phase relationship between voltage and current waveform.
5. An alternating current varying sinusoidally with a frequency of 50 Hz has an rms value of 20 A. a) Determine the instantaneous value at 0.0025 seconds. b) Determine the instantaneous value, 0.0125 seconds after passing through a positive maximum value. c) At what time, measured from a positive maximum value, will the instantaneous current be 14.14 A?
(a) What is the frequency in Hertz and rad/s of the voltage waveform shown on Figure Q1? (b) Calculate the average voltage and rms ac voltage of the waveform shown on Figure Q1. (c) Calculate the total rms voltage of the waveform shown on Figure Q1. (d) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor.
Please need correct answer fast Q1)
Find the RMS value..
6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer must be in polar form and should be in 4 decimal places). -j4 N j1.5 A B 4 0 A 200/30° V -j2 N: jIN Figure 1.
Get the RMS and average value of the voltage. Frequency is 60 Hz. Please write properly the solution. Make sure to recheck.
2.3 please
A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 30 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.8 cm and the peak to peak distance is 4.8 cm. Determine the following: The frequency is? The magnitude of the sine voltage is? The amplitude is? The R.M.S voltage is?
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002