7. A power station has to meet the following load demand : 50 kW Load 4 between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (f) diversity factor () units generated per day (äi) load factor.

7. A power station has to meet the following load demand : 50 kW Load 4 between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (f) diversity factor () units generated per day (äi) load factor.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter29: Service-entrance Calculations

Section: Chapter Questions

Problem 2R: a. What is the unit load per ft2 for the general lighting load of a residence? ____ b. What are the...

See similar textbooks

Similar questions

Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
2. a) Explain the terms load factor and diversity factor. b) Discuss the advantages of interconnected grid system. c) A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Calculate: (i) the maximum demand on the station, (ii) annual energy supplied by the station and (iii) suggest the installed capacity and the number of units.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
For a power station the yearly load duration curve is a straight line from 40,000 to 3000 kw. To meet the load three turbo-generators are installed. The capacity of two generators is 15,000 kw each and the 3d is rated at 6,000 kw. Determine the following a) Load factor. b) Capacity factor. c) Maximum demand.
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
The peak load on a 50 MW power station is 39 MW. It supplies power through for transformers whose connected loads are 17, 12,9 and 10 MW. The maximum demands on these transformers are 15, 10, 8 and 9 MW respectively. The annual load factor is 50% and the plant is operating for 65% of the period in a year. 102. The average load on the station is (A) 50000 kW (C) 39000 kW (B) 19500 kW (D) 48000 kW. 103. The energy supplied per year is (A) 438 x 106 kWh (C) 170.82 x 106 kWh (B) 341.64 x 106 kWh (D) 420.48 x 106 kWh.
The indication of a lagged demand meter approaches the value of the actual load at a rate which is proportional to A. Quotient of the load and the meter indication. B. product of the load and the meter indication C. Difference between the load and the meter indication D. sum of the load and the meter indication
As seen in the figure, three generators of 800 kW, 900 kW and 1000 kW are connected in parallel. It generators feed 380 kW load. Frequency-active power graphs of generators are shown as given. According to this; a. Calculate the operating frequency for the situation given in the question.b. Calculate the power transferred by the generators to the load.c. A three-phase asynchronous load of 800 kW and 600 kVA with a reverse power coefficient of 0.78 is installed in the system. engine is connected. The new operating frequency of the system and the active power of the alternators. calculate.d. Do you think the generators in this system are suitable for parallel connection as in the figure?
An alternator with internal vallage of 125, p.u. and synchronous reactance of 0.4 p.u. is connected by a transmission line of reactance 0.1 p.u. c a synchronous meto having synchronous reactance 2.35 p u. and internal voltage of 0.85/6, p.u. If the real power supplied by the alternator is D 806 p... than (8, & is. degrees. (Round off to 2 decimal places) (Machines are of non-salient typa. Naglact resistances)
A 3-phase star connected, 1500 kVA, 13 kV alternator has an armature resistance of 0.9 ohm and a synchronous reactance of 8.0 ohms. When carrying rated load voltage, calculate the generated voltage per phase at loads of I.) Unity P.F. ii.) 0.8 lagging P.F. iii.) 0.8 leading P.F. iv.) calculate the voltage regulation for each load and determine best regulation.
Sub:Distribution