Suppose you want to use a hydraulic hoe and a fleet of trucks on an excavation project. If you calculate the hydraulic hoe's loading cycle time at 2.0 minutes and the truck cycle time at 25.0 minutes, what is the minimum number of trucks that you would need if you wanted the hydraulic hoe to control production? Group of answer choices 12 12.5 13 50

Suppose you want to use a hydraulic hoe and a fleet of trucks on an excavation project. If you calculate the hydraulic hoe's loading cycle time at 2.0 minutes and the truck cycle time at 25.0 minutes, what is the minimum number of trucks that you would need if you wanted the hydraulic hoe to control production? Group of answer choices 12 12.5 13 50

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter10: Pricing Excavation And Backfill

Section: Chapter Questions

Problem 7RQ

See similar textbooks

Similar questions

Redo Problem 12.30 assuming that the water table coincides with the top of the fill and that sat(fill) = 19.8 kN/m3. If the other quantities remain the same, what would be the downward drag force on the pile? Assume ' = 0.5fill. 12.30 Figure 12.49a shows a pile. Let L = 15 m, D (pile diameter) 305 mm, Hf = 3 m, fill = 17.5 kN/m3, and fill = 25°. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5fill.
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
Redo Problem 18.10 using the method for estimating the skin resistance. 18.10 A concrete pile 15 m long with a cross section of 380 mm 380 mm is fully embedded in a saturated clay layer. For the clay, sat = 18 kN/m3, = 0, and cu = 80 kN/m2. Assume that the water table lies below the tip of the pile. Determine the allowable load that the pile can carry (FS = 3). Use the a method to estimate the skin resistance.
A steel pile (H-section; HP 360 1.491; see Table 18.1) is driven into a layer of sandstone The length of the pile is 18.9 m. Following are the properties of the sandstone: Unconfined compression strength = qu(lab) = 78.7 MN/m2 Angle of friction = 36 Using a factor of safety of 3, estimate the allowable point load that can be carried by the pile. Use Eq. (18.42).
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
For the drilled shaft described in Problem 19.7, determine these values: a. The ultimate load-carrying capacity b. The load-carrying capacity for a settlement of 25 mm Use the procedure outlined in Section 19.8. 19.7 Figure 19.16 shows a drilled shaft without a bell. Here, L1 = 6 m, L2 = 7 m, Ds = 1.5 m, cu(1) = 50 kN/m2, and cu(2) = 75 kN/m2. Find these values: a. The net ultimate point bearing capacity. Use Eqs. (19.23) and (19.24) b. The ultimate skin resistance. Use Eqs. (19.26) and (19.28) c. The working load, Qw (FS = 3) FIG. 19.16