GIVEN:Three-phase System Data:Зф SourceZine30 LoadEan = 12020° v; Epn = 1202 - 120° v; Een = 1204120° v (grounded neutral)Zan = Zbn = Zen = 0.1 + j1.5 nSource:Line Impedance:Zine aZline b= Zline c = 1 +j2 N;Load Impedance:Zab = 40 + j30 N; Zbc = 40 – j30 N; Zca = 50 + j0 N%3DTypes of Faults to be Considered, assuming worst case scenario (Zf = 0):SLGF (line a grounded), LLF (lines a & b connected), 1LO (line a open)FIND:please answer in 4 decimal placesUnder Unbalanced Condition With Faults:a. Load Line Currents (Ia, Ib,lc);b. Load Line Voltages (Vab, Vpc, Vca);

Answered: Image /qna-images/answer/88f25094-463b-485d-9932-2c5300040b46.jpg

Source: Ean = 12040° v; Epn = 120-120° v; Een = 1204120° v (grounded neutral) Zan = Zpn = Zen = 0.1 + j1.5 N Line Impedance: Zline a = Ztine b = Ztine c = 1+ j2 N; Load Impedance: Zab = 40 + j30 ; Zbc = 40 – j30 N; Zca = 50 + j0 N Types of Faults to be Considered, assuming worst case scenario (Z, = 0): SLGF (line a grounded), LLF (lines a & b connected), 1LO (line a open) FIND: please answer in 4 decimal places Under Unbalanced Condition With Faults: a. Load Line Currents (Ia, Ip,Ic); b. Load Line Voltages (Vab, Vpc, Vca);

Source: Ean = 12040° v; Epn = 120-120° v; Een = 1204120° v (grounded neutral) Zan = Zpn = Zen = 0.1 + j1.5 N Line Impedance: Zline a = Ztine b = Ztine c = 1+ j2 N; Load Impedance: Zab = 40 + j30 ; Zbc = 40 – j30 N; Zca = 50 + j0 N Types of Faults to be Considered, assuming worst case scenario (Z, = 0): SLGF (line a grounded), LLF (lines a & b connected), 1LO (line a open) FIND: please answer in 4 decimal places Under Unbalanced Condition With Faults: a. Load Line Currents (Ia, Ip,Ic); b. Load Line Voltages (Vab, Vpc, Vca);

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1 Two transformers A and B are connected in parallel to a load of (2+j1.5)2. Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and ZB= (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 /0° volt and EB = 205/0° volt. Find the power output and power factor of each transformer.
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Q2
For the bridge circuits shown in the figure bellow, derive expressions to calculate the unknown impedances. Be Detector wwlle
Hello, please help me with my calc assignment asap.Please show all works so I can understand how it works and box the answer.I need help asap.Thank you so much for your help.
thats it
Determine the value of the impedance, Z₁, that causes maximum power transfer in the circuit shown in Figure Qlc. 52 j24n -j12.35n (V₂) j2403 j24n Figure Qle B
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
A. 3-8 50kw, 4-pole, soHZ inducffon motor haß a coinding Cacy desigmed for delta connection. the coinding has 24 conducforx por Mot mranged in Go slots, the mo value * the line current is 48A. Aind the fumdomental of the mmf coane f phase -A when the cunnent is passing throyph its maximum value. what ig the speed and peak volue the resultant mmf/ pule. folne il sume otheroise &leip. Al ame incorreet dorit copy fom Qne Anscwor Another Ansawer
3. A circuit consists of two impedances. Z1 =20230° and Z2 =25260° 2, in parallel, supplied by a source voltage V=1002600 volts. Determine the power triangle for each of the impedances and for the source.