VI) For the circuit shown, answer the questions from 15-19. The load Zt = 8+j6 ohms, and thesource frequency is 50 Hz. (voltage source values is given is RMS, ABET assessment #2)ーリ刺jó 2100/0° V17Z87,7loole =ーリP=18,19uFEW 50 loo80017) The capacitor current is.... A:a) j3.37e) j5.64b) -jl.33Dj1.33c)-j5.64g) 2.67 22.36°d) 2.65 Z-85.23°h) None of the abovelo L36 67

Answered: Image /qna-images/answer/672464e3-8a0a-4e56-87fc-502c6b13fc95.jpg

VI) For the circuit shown, answer the questions from 15-19. The load Zt = 8+j6 ohms, and the source frequency is 50 Hz. (voltage source values is given is RMS, ABET assessment #2) ーリ刺 jó 2 100/0° V loole = ーリ P= 8+6)-11 18,19 EW.50- loo 800 17) The capacitor current is... A: a) j3.37 e) j5.64 b) -jl.33 Dj1.33 c)-j5.64 g) 2.67 22.36° d) 2.65 -85.23° h) None of the above lo L36 62

VI) For the circuit shown, answer the questions from 15-19. The load Zt = 8+j6 ohms, and the source frequency is 50 Hz. (voltage source values is given is RMS, ABET assessment #2) ーリ刺 jó 2 100/0° V loole = ーリ P= 8+6)-11 18,19 EW.50- loo 800 17) The capacitor current is... A: a) j3.37 e) j5.64 b) -jl.33 Dj1.33 c)-j5.64 g) 2.67 22.36° d) 2.65 -85.23° h) None of the above lo L36 62

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5) A balanced three-phase source of 4160 V is feeding a balanced three-phase induction motor through a cable of negligible impedance. The induction motor draws 400 kW at 0.8 power factor lagging. Calculate the reactive power consumed by the induction motor. Design two different techniques to improve the overall power factor from 0.8 to 0.96 lagging. Show the effectiveness of your design through a numerical example. i) ii)
7.5 The input voltage to the single-phase, to single-phase cycloconverter is boiqui 240V(rms), 50Hz. The load resistance is 1002 and the load inductance is Jugo L = 50 mH. The frequency of the output voltage is 25Hz. If the converter is operating with a delay angle ap=2π/3, anonimo guide in 19 um 926riq (a) Sketch the circuit configuration of the converter. vitoid nad (b) Sketch the output voltage waveform.ddgue Shovno aid (c) Determine the rms value of the output voltage. turli 101 anos (d) Determine the impedance of the load at the outut frequency. eved jedi ame) Calculate the rms value of the load current. of sub 918 19 (f) Determine the input power factor of the converter. bowola
Explain why the maximum value of the duty cycle must be limited in certain boost choppers. //(L-7)
21) A. A three phase fully controlled bridge converter is supplied from 400V, 50Hz, three phase mains and operates at firing angle 45°.If the current on load side is constant at 8A and the load voltage is 230V, calculate the source inductance and overlap angle. Derive relevant formula.
3. A 12020⁰ Vrms is to supply power to a welder, heater and an induction motor. A welder is a coil of (4+j3) ohm, the induction motor draws 60KW with 0.8 power factor, and the heater is a resistor that draws 15KW power. Find the complex power, real power, reactive power and the total power factor that must be supplied by source. If a capacitor will be used to supply a reactive power in the circuit in order that the net load will have a unity power factor, what reactive power must be supplied by the capacitor? Draw the circuit.
A 6 pole DC wave wound generator has 28 armature conductors with flux per pole is 23 mWb and the e.m.f generated is 64 V, then the speed of the machine is O 99.38 rps O 0.63 rps O 33.13 rps O 6.34 rps The thermocouples are suitable for temperature measurement applications in the range of 200°C to over 2000°C. Select one: O True O False
30. In the circuit of Figure P28.30, determine (a) the cur- W rent in each resistor and (b) the potential difference across the 200-2 resistor. + 40.0 V 360 V 80.0 V + 200 Ω 80.0 Ω 20.02. Figure P28.30 70.02. +
The concentration ratio of parabolic trough power plant is typically O a. from 30 to 40 O b. more than 1500 O c. less than 10 O d. from 10 to 20
A three phase full controlled converter is supplied by a phase voltage Vs=120V, 60 Hz. Consider a resistive load R=10 Q. If the RMS value of the output current is equal to 10.94A and the input Volt Ampere VA = 3125VA, then the output power P, and the power factor would be equal to: Select one: a. 3196.84W, 0.772 lagging O b. 1196.84W, 0.382 lagging O c. 3196.84W, 0.382 lagging o d. 1196.84W, 0.772 lagging
A single phase voltage controller of 220 V, 50 Hz and a load of 10 Q. For 9 cycles on and 7 cycles off the rms output voltage and input power factor are: (a) 170 V, 0.7 (b) 165 V, 0.75 (c) 171 V, 0.78 (d) 180 V, 0.6
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.
Q5. A single-phase full-wave ac voltage controller has a resistive load of R = 10 Q and the input voltage is Vs = 120V (rms), 60 Hz. The delay angles of thyristors T1 and T2 are equal ai a2 = a = t/2. Determine (a) the rms output voltage Vo, (b) the input PF, (c) the average current of thyristors Ia and (d) the rms current of thyristors IR.