Vin لفهما V₁ لووفا V₂ 2 www Vout 1:5 Assume the transformer circuit above is ideal, and that R₁ = 1000, R₂ = 4000 and 11.rms = 50 A. Find the rms voltage, V2.rms, across the secondary coil of the transformer. V2.rms [V]:

Vin لفهما V₁ لووفا V₂ 2 www Vout 1:5 Assume the transformer circuit above is ideal, and that R₁ = 1000, R₂ = 4000 and 11.rms = 50 A. Find the rms voltage, V2.rms, across the secondary coil of the transformer. V2.rms [V]:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Related questions

Q: A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase.…

Q: onsider a three winding transformer with the following particulars: = 50-40° A. Assume that V₂ is 1=…

A: Solution- THREE WINDING TRANSFORMER Given, Z1=Z2=Z3 = 0.02+j0.08 ohmV2 = 400 VI2 = 60∠-30° AI3…

Q: The equivalent resistance of the primary of a transformer having K = 6 and R1 = 0.2 ohm when…

Q: Another name for the RMS value of current or voltage is ... the effective value the exact value the…

A: RMS: RMS value is the value at which the heat produced by AC waveform is same as the heat produced…

Q: A 3-phase induction motor delivers 74,600 watts while operating at an efficiency of 80 percent and a…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Vin
V₁
leee
liee
V₂
R₂
ww
Vout
1:5
Assume the transformer circuit above is ideal, and that R₁ = 1000, R₂ = 4000 and 11,rms = 50 A.
Find the rms voltage, Vzrms, across the secondary coil of the transformer.
V2.rms [V]:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

helpp
b) A circuit with an ideal transformer is shown in Figure Q5 (b). The source has an effective value of 100 V rms, and the load is Zz = 400+j400 2. Let N₁ = 100 turns and N₂ = 500 turns, find the average power delivered to the load. N₁ : N₂ 12, R₁ = 102 Figure Q5 (b) V₂ Z₁
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Design a flyback converter for an input of 24 V and output of 40 W at 40V. Specify the transformer turns and magnetizing inductance, switching frequency and capacitor to limit the ripple voltage less than 0.5%.
Please answer all questions 1. Calculate the magnitude (in RMS) of the current through R1 2. Calculate the magnitude (in RMS) of the current through R2. Simulation 1. Construct the circuit in Figure 2 in the Circuit JS simulator. Note that transformers in Circuit JS may be unstable. It is suggested to draw them by clicking from the bottom left corner to the top right corner and refresh your simulation before taking a measurement. 2. Perform a simulation, displaying the voltage across the voltage source, the current through R1, and the current through R2 in a “stacked” scope. Display the RMS average for each trace. Include a screenshot. Analysis 1. Compare the simulation results for the currents through R1 and R2. What is the percentage difference between the calculated and simulated value for each? Comment on why there may be a discrepancy.
A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
help please
An ideal transformer has 500 turns on the primary and 300 turns on the secondary. The source produces a voltage of 600V (RMS) and load Z is a pure resistance of 122. Calculate: (i) E2 (ii) Il & 12 (iii) Power delivered to the primary (W) (iv) Power output from secondary (W) 2. (v) what is the impedance seen by the source?
the rest of the question says "...the source. What is the efficiency of the transformer? [Hint: Efficiency is defined as the ratio of the output power to the input power.]
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor