A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source

A 220V(rms), 50HZ sinusoidal source is connected to the primary side of an ideal transformer with 100 turns on the primary side and 300 turns on the secondary side. Primary line resistance is 22 and inductance is 10mH. Secondary line resistance is 92 and inductance is 100mH. There is a 1002 resistive load connected on the secondary side. Draw a well-labeled circuit diagram and determine: (i) Currents on both sides (ii) Load Voltage (iii) Complex power supplied by the source

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Both why and delta None of the above Q10. In a transformer modeling, the value of the voltage referred to primary side is [N/N2 ]*V2 [N/N, ]*V2 O(N/N2 1*V1 O [N/N, ]*V1
A multitap transformer has 1500 turns on the primary, 100 turns between B and C, 600 turns between A and D, and 500 turns between A and C. Calculate the secondary voltage between A and B if a 240V RMS source is connected to the primary. OB O A 134V RMS O 240V RMS O 96V RMS O 64V RMS
2.Fringing effect is a phenomena occurs in... (a)Transformers. (b) Electrical field. (c) Air gap (d) All of the above. 3. The kVA rating of an ordinary 2-winding transformer is increased when connected as an autotransformer because (a) transformation ratio is increased (b) secondary voltage is increased (c) energy is transferred both inductively and conductivity (d) secondary current is increased. 4. The....... of the hysteresis loop is a measure of energy lost per cycle (a) area. (b) Type. (c) Frequency (d) No one of the above. 5. At relatively light loads, transformer efficiency is low because (a) secondary output is low (b) transformer losses are high (c) fixed loss is high in proportion to the output (d) Cu loss is small. 6. In an ideal transformer, (a) windings have no resistance (b) core has no losses (c) core has infinite permeability (d) all of the above. 7. In electromagnetic circuits, path of eddy current is........ (a) Parallel to the path of the flux. (b) Perpendicular to…
Transformers
A single-phase semi-converter is operated form 120 V, 50 Hz AC supply at a firing angle of 30 degrees. The load is such that the load current is continuous and ripple-free. Displacement factor of the converter is: (a) 0.77 (c) 0.67 (b) 0.97 (d) 0.57
The table below shows some performance parameters of a certain power transformer. Full-load voltage regulation Full-load copper loss Load power factor 5% 0.5 Lagging Zero voltage regulation is obtained at a load power factor of: 0.9176 leading 08 leading 0.397 lagging 2% 0.703 leading
q9
Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five customers. Daily maximum demands for these customers are 120 kW, 40 kW, 90 kW, 110 kW, and 180kW. The maximum demand on the feeder is 243kW. The coincident factor of the feeder is
Which of the following quantities is increase in a step-down transformer? Current Voltage O Power O Frequency
Tansformers
FInd output voltage and output current for the given power supply
A transformer has a rated output of 400 kVA at a power factor of 0.6. Determine the rated power output and the corresponding reactive power.