c) Figure 6 is the waveform of output voltage, vo from synchronous connection changer. The primary voltage is 220 V (rms), 60 Hz. The secondary voltages are Vi = 120 V and V2 = 100 V. If the load resistance is R = 6 Q and the rms load voltage is 150 V with delay angle, a = 93°, determine the; i. rms current of thyristors T1 and T2. ii. rms current of thyristors T3 and T4. iii. input PF. V2(V1 + V2) of Figure 6

c) Figure 6 is the waveform of output voltage, vo from synchronous connection changer. The primary voltage is 220 V (rms), 60 Hz. The secondary voltages are Vi = 120 V and V2 = 100 V. If the load resistance is R = 6 Q and the rms load voltage is 150 V with delay angle, a = 93°, determine the; i. rms current of thyristors T1 and T2. ii. rms current of thyristors T3 and T4. iii. input PF. V2(V1 + V2) of Figure 6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

"As per the standards used in power system, even harmonics are limited to 25 percent of the odd harmonic limits" True False
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
A series resistance – capacitance (R – C) circuit is connected to 230 – volt, 50 cycle AC source. The current through the resistor is 45.45 A and the power taken by the circuit is 5,000 watts. Compute the following: 1.) Power factor angle 2.) Circuit impedance 3.) Ohmic value of the resistor
A 220 V, 60 Hz voltage is applied across a series circuit figure comprising a coil of resistance R, inductance L, and capacitor C, determine: (a). The impedance of the circuit. (b). The current flowing in the circuit. (c). The voltage developed across the inductor. (d). The voltage dropped across the capacitor. (e). The voltage dropped across the resistor. (f). The phase angle. 220 v 60 Hz R = 25 Q2 C= 100 μF R L V₁ V 70 1 L= 6 mH C Ve
2
What is the effective value of 200 volts peak-to-peak? A. 70.7 V. B. 141.4 V. C. 14.14 V. D. 707.0 V.
* A single phase half wave AC voltage controller comprises of thyristor connected with parallel power diode O parallel thyristor anti parallel thyristor parallel thyristor O A single phase full wave AC voltage controller comprises of thyristor connected with parallel power diode O anti parallel power diode parallel thyristor anti parallel thyristor O
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.
How is inductive reactance in alternating current circuits?
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
A single phase full wave ac/ac converter's input voltage is Vs (rms)= 220 Volt. The firing delay angles are a1= n/2 and a2=3 n/2 respectively Which one is the rms value of the output voltage ?
Don't use ai to answer I will report your answer .. Solve it Asap with explanation and calculation