(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZRY = 50 + j50 2, ZYB = 150 + j0 2 and ZBR= 50 –j50 2. (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.

(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZRY = 50 + j50 2, ZYB = 150 + j0 2 and ZBR= 50 –j50 2. (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
5.7. In Figure P5.7, the voltages at a, b, and c are balanced 30. Transformers are ideal and have the same turns ratio. Find the voltages Va, Vic, and Vea in terms of Vab, Vher and V ca (a) Are they balanced 30? (b) If not, how would you reconnect the transformers to obtain balanced 36? a rele b 6 b' 000 ( Figure P5.7
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
3. A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1 + j1 Ohms, and the secondary impedance is 0.2 + j0.2 Ohms. Assume the core impedance (R0 and X0) can be neglected. A resistive load of 12 Ohms is connected to the secondary. What is the primary current magnitude? What is the secondary voltage magnitude? What is the efficiency of this transformer with this load?
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
1 Two transformers A and B are connected in parallel to a load of (2+j1.5)2. Their impedances in secondary terms are ZA = (0.15 + j0.5)2 and ZB= (0.1 +j 0.6)2. Their no-load terminal voltage are EA 207 /0° volt and EB = 205/0° volt. Find the power output and power factor of each transformer.
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
How to solve for a (+) Phase Sequence and (-) Phase Sequence? Give an example and explain the steps.
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. N1=200 NBC=20 N2=100 NBA=30 10A B 200 V 50,Hz C N1: N2