SITUATION. A hollow steel strut is pin connected to two gusset plates. The gusset plates are then welded to a 12 mm thick base plate which is fastened to a concrete base with 4 anchor bolts. The strut carries an axial compressive load of 48 kN at a 30-degree angle with the horizontal. If the allowable shearing stress in the pin is 120 MPa, shearing stress in the anchor bolts is 52 MPa, bearing stress between the strut and pin is 150 MPa, and the bearing stress between the anchor bolt and the base plate is 117 MPa, determine the following 1) Required diameter of the pin 2) Required thickness of the strut 3) Required diameter of the anchor bolts 4) Required thickness of the gusset plate 48kN Steel Strut Give your answers in mm, in whole numbers. Gusset Plate Anchor Bolt

SITUATION. A hollow steel strut is pin connected to two gusset plates. The gusset plates are then welded to a 12 mm thick base plate which is fastened to a concrete base with 4 anchor bolts. The strut carries an axial compressive load of 48 kN at a 30-degree angle with the horizontal. If the allowable shearing stress in the pin is 120 MPa, shearing stress in the anchor bolts is 52 MPa, bearing stress between the strut and pin is 150 MPa, and the bearing stress between the anchor bolt and the base plate is 117 MPa, determine the following 1) Required diameter of the pin 2) Required thickness of the strut 3) Required diameter of the anchor bolts 4) Required thickness of the gusset plate 48kN Steel Strut Give your answers in mm, in whole numbers. Gusset Plate Anchor Bolt

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Point B of the system given below is movable support and Enpoint is fixed bearing. According to the given loading condition a) Draw the normal force, moment and shear force diagrams. B) Check whether the section used between AB-BC-CD is suitable, as the material has normal allowable stress em = 85 Mpa and shear strength em = 50 Mpa. c) Find the diameter d of the section used between DE-EF since the normal allowable stress of the material is em = 85 Mpa and the shear strength is em = 50 Mpa.
show complete solution. Thanks!
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moment. Fc'= 40 Mpa.
For the beam and loading shown, determine the maximum normal stress due to bending on section a-a
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Put detailed solution and free body diagram. The topic is shear and bearing stresses.
A rectangular beam 200 mm wide has an effective depth of 350 mm. It is subjected to a bending moment of 24,000 Nm. The permissible stresses are c = 5 N/mm², t = 140 N/mm²; and m is 18. The required area of tensile reinforcement will be.
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths
Problem 2: The center post B of the assembly has an original length of 124.8mm whereas posts A and C have a length of 125mm. If the caps on top can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400mm2. EAI = 70 GPa loomn A