PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the required thickness t of C and D so that all strips will fail simultaneously. The width of strips A and B is 1.75 times that of strips C and D. b. Compute the axial stress in strips A and B if the width of C and D is 300mm. c. Compute the shearing stress if the gap between A and B at the center is to be neglected and the length of D is 500mm and the width is the width computed in (a).

PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the required thickness t of C and D so that all strips will fail simultaneously. The width of strips A and B is 1.75 times that of strips C and D. b. Compute the axial stress in strips A and B if the width of C and D is 300mm. c. Compute the shearing stress if the gap between A and B at the center is to be neglected and the length of D is 500mm and the width is the width computed in (a).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the stresses in two segments of the bar shown. Segment A has a diameter of 1 and1/4 inches and segment B has a cross-section 2in by 2in
2. Maximum tensile and compressive bending stress, Make W= 8 kN/m all dimensions are in mm make answer rounded off into 3 decimal places.
Problem 3 For the shown beam. (1) Plot V and M diagram (2) Find the maximum tensile and compressive flexural stresses in the beam and indicate the location (both on beam and cross-sectional area) 2 in. 2 in. 2 in. 2000 lb 800 lb/ft 4000 1b ft B 6 in. 2 in. 3 ft 10 ft 2 ft- (a) (b)
Explain the term principles of superposition in civil engineering structures. b.State and explain the type of support below, draw the FBD and sketch the shear force and bending moment of each 6c.On load application point of the engineering structural member show below. Explain in detail, the alternative load application direction on the material (include the names and formulas) and examine the following 1)Necking 2)Failure 3)P 4)Ao 5)Lo
The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.5* ? inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 4.5* ? ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.
Determine the maximum tensile and compressive bending stresses in the beam show.
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
Determine normal stresses at A and B. Are these point of maximum and minimum normal stresses? If not where are they located and what their values.
(b)If the cross-section of the beam is as shown below, determine the maximum tensile and compressive stresses. E 8 in. 1 in. 1 in. 6 in. I in. 4 in.
1.61.The state of stress at a point relative to an x, y, z coordinate system is given by 12 4 2 4 -8 -1 MPа -1 6. Calculate the maximum shearing stress at the point.
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12)
Given: Four-25-mm-diameter rivets with an axial load of T = 75 kN distributed equally as shown. The thickness of the plates is 25 mm and the width of the plate is 150 mm. find (a) the shear stress on the rivets (b) the bearing stress between a plate and a rivet; (c) the minimum average tensile stress in each plate. Show detailed solution and draw FBD.